background image

Knife Loop Yak 3D 

Aerobatic Profile ARF 

 
 

 

 

Instruction Manual 

 
 

Warranty 

 
Merlin Hobbies (

www.merlinhobbies.com

) guarantees this kit to be free from defects in both material and 

workmanship at the date of purchase.  This warranty does not cover any component parts damaged by use 
or modification.  In no case shall Merlin Hobbies liability exceed the original cost of the purchased kit.  
Further, Merlin Hobbies reserves the right to change or modify this warranty without notice. 
 
Since Merlin Hobbies has no control over the final assembly  or material used for final assembly, no 
liability shall be assumed, nor accepted for any damage resulting from the use by the user of the final user 
assembled product.  By the act of using this product, the user accepts all resulting liability. 
 
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is 
advised to return this kit immediately in new and unused condition to the place of purchase. 
 
While this kit has been flight tested to exceed normal use, if the plane will be used for extremely high stress 
flying, such as racing, the user is responsible for taking steps to reinforce the high stress points. 
 
Read through this manual before starting construction.  It contains important warnings and instructions 
concerning the assembly and use of this model. 
 
 

Summary of Contents for Knife Loop Yak 3D














Reviews: