Merits S331 series Page 21 Service Manual Download

Page: 21 / 24

2.5.4. To replace the regulation cylinder

◆

When should you replace the regulation cylinder?

◇

If the regulation cylinder out of shape due to an accident.

◇

If the regulation cylinder is deformation.

◇

If the clearance is too much to cause the tiller assembly shake.

◆

How to replace the regulation cylinder?

◇

Please proceeding steps as follows if it has to replace.

  1. Loosen the screw and nut which mounted on the lever. (5.05)
  2. Take out the lever (5.05) with cable/wire (5.06) from tiller frame.
  3. Loosen the screw (5.08) and nut (5.10) by hex. tools and wrench then

loosen the screw (5.16) (5.17) by hex. tools only.

4. Take out the regulation cylinder (5.07)

、

cable/wire (5.06) and lever

(5.05) from the tiller frame together.

2.5.5. To replace the dashed board assembly

◆

When should you replace the dashed board assembly?

◇

If your dashed board assembly is deformation.

◇

If the dashed board assembly out of shape due to an accident.

◇

If your control units & harness is deformation.

◆

How to replace the dashed board assembly?

◇

Please proceeding steps as follows if it has to remove.

1. Loosen the screw (5.20)*4pcs by screw driver.
2. Unplug the 3 connectors which from the throttle lever assy’ (5.3) and

main cable loom (5.83).

3. Take out the dashed board assembly from frame.

Summary of Contents for S331 series

























Search results

Summary of Contents for S331 series

Reviews:

Related manuals for S331 series

Brands by name

Popular brands

Merits S331 series, Service Manual

Search results

Summary of Contents for S331 series

Reviews:

Related manuals for S331 series

Brands by name

Popular brands