Meritor MM-0861 Maintenance Manual Download Page 112

Page: 112 / 118

MM-0861 / Revised 06-22
Page 110

Printed in USA

14 Tools

Bearing Driver (4FI20-27110-000008-D01)

4012347a

0.389

0.250

30°

R0.06

R0.125

0.13 X 45°

(2) PLACES

TOOL A

0.50

R0.12

0.02 X 45°

(2) PLACES

4.95

2.25

2.50

4.45

Ø0.80

1.83

Ø2.743

Ø2.148

Ø3.25

Ø2.582

Tool Assembly Instructions:

1. Install Tool B, bearing driver guide, into the bore of Tool A, bearing driver.

2. Install a 3/16" O.D. x 1/2" long roll pin through the 1/4 x 2-1/2" long slot of Tool A,

and into the 3/16" hole in Tool B. The roll pin can be obtained from McCaster Carr,

part number 98296-A975.

QTY (2)
4140 PRE-HARDENED

Figure 14.4

Bearing Driver Guide (4FI20-27110-000008-D02)

4012354a

0.250

Ø1.608

3.125

Ø2.108

0.13X45°

0.06X45°

3/16 DRILL

THRU BOTH

SIDES (HOLE

FOR ROLL PIN)

SEE TOOL ASSEMBLY INSTRUCTIONS

3.625

1.375

R0.250

TOOL B

QTY (2)
4140 PRE-HARDENED

Figure 14.5

Summary of Contents for MM-0861























































































































Search results

Summary of Contents for MM-0861

Reviews:

Brands by name

Popular brands

Meritor MM-0861, Maintenance Manual

Search results

Summary of Contents for MM-0861

Reviews:

Brands by name

Popular brands