Mercusys ME20 User Manual Download Page 32 | Manualshive

Page: 32 / 36

background image

25

Chapter 5 Manage the Extender

3. Click

SAVE

.

5.4

Upgrade the Firmware

You can download the latest firmware file from the

Support

page at our website

www.mercusys.com

and upgrade the extender to the latest firmware version.

Note:

•

Make sure the latest firmware file is matched with the hardware version.

•

Make sure that you have a stable connection between the extender and your computer. It is NOT

recommended to upgrade the firmware wirelessly.

•

We strongly recommend you back up the current configuration settings before firmware upgrade.

•

Do NOT power off the extender during the firmware upgrade.

1.

Download the latest firmware file for the extender from our website

www.mercusys.com

.

2.

Visit

http://mwlogin.net

, and log in with the password you set for the extender.

3. Go to

Settings

>

System Tools

>

Firmware Upgrade

.

4.

Click

BROWSE

to locate the downloaded new firmware file, and then click

UPGRADE

.

5.

Wait a few minutes for the firmware upgrade to complete and the extender to
reboot.

5.5 Back up and Restore Configuration Settings

The configuration settings are stored as a configuration file in the extender. You can
back up the configuration file and restore the extender to the previous settings from
the backup file when needed. Moreover, if necessary, you can erase the current
settings and reset the extender to the default factory settings.

«
...
30
31
32
33
34
...
»

Summary of Contents for ME20





































Reviews:

No comments

Related manuals for ME20

Brand: SEVERIN Pages: 42

Brand: Wi-Ex Pages: 17

DL-DVI-Vision-Fiber-AR-CON

Brand: G&D Pages: 136

Brand: Atlona Pages: 10

Brand: Novis Pages: 144

Brand: Wyrestorm Pages: 4

Brand: Zelmer Pages: 30

JTC OmniBlend V TM-800

Brand: saro Pages: 10

Brand: Electrolux Pages: 36

Brand: Electrolux Pages: 32

Brand: Electrolux Pages: 40

Brand: Electrolux Pages: 21

Brand: Electrolux Pages: 36

Brand: Electrolux Pages: 44

Brand: Electrolux Pages: 40

Powermix Mini EMB4100

Brand: Electrolux Pages: 46

UltimateTaste 500

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands