manualshive.com logo in svg

Mercury Zeus 3000 Series, User Manual

Share
Download
Mercury Zeus 3000 Series User Manual Download Page 60

Section 3 - On the Water 

Page  52

90-866938081   MAY  2009

• On  the  right  side  of  the  screen,  an  icon  labeled  "OFF"  indicates  that  Pilot  is  not

engaged.

NOTE: Not all of the functions of Precision Pilot work when DTS functions are engaged.

Disengage the DTS functions to use the functions of Precision Pilot.

31408

b

c

a

d

Standby screen on VesselView

a -

"OFF" icon

b -

Heading

c -

Drive angle reference

d -

Engine RPM

STANDBY AND ACTIVE LIGHTS

Precision Pilot is disengaged (off) when the "STANDBY" light is illuminated. You must press

the button for Auto Heading, Track Waypoint, or Skyhook to engage a mode.
When the "ACTIVE" light is illuminated one mode of Precision Pilot is engaged (on).

27695

a

b

a -

"STANDBY" light

b -

"ACTIVE" light

Summary of Contents for Zeus 3000 Series

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands