manualshive.com logo in svg

Mercury Zeus 3000 Series, User Manual

Share
Download
Mercury Zeus 3000 Series User Manual Download Page 101

Section 5 - Maintenance

90-866938081   MAY  2009

Page  93

a.

Insert the molded clip on the aft end of the hatch cover under the indented‑edge

of the cover.

a

c

b

39506

a -

Hatch cover

b -

Molded clip

c -

Indented‑edge

b.

Align the access cover with the opening in the top cover.

c.

Press down evenly on the front of the access cover. A click‑sound can be heard

when the access cover snaps into final position.

39514

Completing the access cover installation

Filling

If the gear lube level is below the "COLD FILL LEVEL" line, add the specified gear lube.
1. Remove the cap from the gear lube monitor.

a

b

41465

Shown without drive cover

a -

Gear lube monitor

b -

Cap

NOTE: The Premium Gear Lubricant used during the break‑in period is brown in color. The

color of High Performance Gear Lube, used after break‑in, is blue. Do not mix the gear

lubricants.

Summary of Contents for Zeus 3000 Series

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands