manualshive.com logo in svg

Mercury Racing HP1200 SCi Dry Sump, Operation, Maintenance & Warranty Manual

Share
Download
Mercury Racing HP1200 SCi Dry Sump Operation, Maintenance & Warranty Manual Download Page 98

TROUBLESHOOTING

90

Engine Cranks But Will Not Start

Possible Cause

Remedy

Improper starting procedure

Read starting procedure

Low battery voltage

Charge the battery

Empty fuel tank or fuel shut off valve

closed

Fill tank or open valve

Faulty fuel pump, wiring, fuel pump

fuse, 50 amp circuit breaker or a fuel

pump relay

Replace faulty component

Faulty ignition system component

Service ignition system

Lanyard Stop Activated

Reset

Obstructed fuel filter

Replace filters

Stale or contaminated fuel

If contaminated, drain tank and fill with

fresh fuel

Fuel line or tank vent line kinked or

restricted

Replace kinked lines or blow out lines

with compressed air to remove

obstruction

Crankshaft position sensor faulty

Test and replace if faulty

Faulty fuel pressure regulator

diaphragm

Test and replace if faulty. Do not

attempt to start the engine if the fuel

pressure regulator diaphragm is

ruptured.

Summary of Contents for HP1200 SCi Dry Sump











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands