MerCruiser QSD 2.0 Manual Download Page 94

Page: 94 / 135

Section 5 - Maintenance

Page 86

90-8M0057081

eng

MARCH 2011

NOTICE

Failure to close the seawater inlet or seacock when removing or replacing the anode plugs can lead to water damage. Close

the seacock or remove and plug the seawater inlet hose to prevent water from entering the anode plug holes.

2. With the engine off, close the seacock, if equipped, or remove and plug the seawater inlet hose.
3. Drain the seawater system. See

Draining the Seawater System

4. Remove the anode assembly (anode plug, sealing washer, and the sacrificial anode) from the aftercooler end cover.

25583

Seawater system anode assembly location

Cleaning and Inspection

NOTE: Using sandpaper, fiber brush, or cleaning pad, remove the deposits from the surface of the anode before trying to determine

the amount of erosion. Do not use a mild steel brush which might leave deposits that could accelerate corrosion.

1. Remove the deposits.
2. Inspect and measure the anode. Compare the measurements to the specifications for a new sacrificial anode and replace

the anode assembly when deteriorated 50%.

NOTE: Sacrificial anodes are available only as an assembly. Replace both the plug and anode as a unit.

Anode assembly

a -

Anode plug

b -

Sacrificial anode

c -

Length

d -

Diameter

e -

Sealing washer

Sacrificial anode measurements (new)
Length

19 mm ( 3/4 in.)

Diameter

16 mm ( 5/8 in.)

3. Discard the sealing washer.

19226

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands