MerCruiser QSD 2.0 Manual Download Page 79 | Manualshive

Page: 79 / 135

background image

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 71

7. Lubricate the fuel filter seals.

Typical

a -

Water‑separating fuel filter

b -

Seals

Tube Ref No.

Description

Where Used

Part No.

80

SAE Engine Oil 30W

Water-separating fuel filter sealing ring

Obtain Locally

8. Align the filter to the bracket. Twist the filter by hand to secure the filter to the bracket. Do not use a filter wrench.

Typical

a -

Water‑separating fuel filter

9. Ensure that the drain cap is securely tightened.
10. Connect the WIF sensor wires, if equipped.
11. Fill the water‑separating fuel filter with fuel. See

Filling

.

12. Check the filter and drain cap for fuel leaks.
13. Connect the battery cables.
14. Start and operate the engine. Check the filter connection for fuel leaks. If leaks exist, recheck filter installation. If leaks continue,

stop the engine immediately and contact your Cummins MerCruiser Diesel Authorized Repair Facility.

Filling

A type of hand pump and primer plunger is located on the fuel filter bracket and is used to
•

Refill the fuel filter when draining or changing the filter.

•

Refill the fuel system on the engine if the system was run dry.

•

Prime the fuel system if the engine has not been run for an extended period.

IMPORTANT: Only fill the fuel filter with the hand pump and primer plunger to ensure that unfiltered fuel does not get into the fuel

system.

NOTE: Follow this procedure after installing a new filter or if the fuel has been drained from the filter checking for water.

24569

a

b

b

a

23460

«
...
77
78
79
80
81
...
»

Summary of Contents for QSD 2.0








































































































































Reviews:

No comments

Related manuals for QSD 2.0

EC FSE 400 - SERVICE 2002 & 2003

Brand: GAS GAS Pages: 74

Brand: RCGF Pages: 22

Brand: NOVAK Pages: 2

Brand: Oriental motor Pages: 8

Brand: Man Pages: 42

Brand: Man Pages: 48

Brand: IMS Pages: 6

Brand: Toyama Pages: 44

Brand: BMW Pages: 41

Brand: DUROMAX Pages: 70

Brand: Pratt & Whitney Pages: 576

Brand: Honda Pages: 32

Brand: Honda Pages: 100

Brand: Honda Pages: 96

Brand: Honda Pages: 114

Car Engine GX340

Brand: Honda Pages: 96

Brand: Honda Pages: 431

Brand: Continental Refrigerator Pages: 146

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands