MerCruiser QSD 2.0 Manual Download Page 76

Page: 76 / 135

Section 5 - Maintenance

Page 68

90-8M0057081

eng

MARCH 2011

1. Slide the filter element into the air filter housing. Ensure that the element is seated fully into the air filter housing.

a -

Air filter housing

b -

Air filter element

NOTE: The warning labels on the air filter housing must be visible after the air filter housing is installed.

2. Install the air filter housing on to the turbocharger inlet.
3. Tighten the air filter housing clamp to specification.

Description

lb–in.

lb–ft

Air filter housing clamp

5.6

–

4. Install the oil separator vent hose. Tighten the oil separator vent hose clamp securely.

Air filter housing

a -

Air filter housing

b -

Oil separator vent hose

c -

Air filter retaining clamp

5. Tighten the oil separator vent hose clamp to specification.

Description

lb–in.

lb–ft

Oil separator vent hose clamp

5.6

–

Water‑Separating Fuel Filter

WARNING

Fuel is flammable and explosive. Ensure that the key switch is off and the lanyard is positioned so that the engine cannot start.

Do not smoke or allow sources of spark or open flame in the area while servicing. Keep the work area well ventilated and avoid

prolonged exposure to vapors. Always check for leaks before attempting to start the engine, and wipe up any spilled fuel

immediately.

NOTICE

Water entering the fuel injection system will cause corrosion and rusting of the injectors and other components, disabling the

fuel injection system. Check daily for water in the water‑separating fuel filter and have the engine inspected immediately if there

is evidence of water in the fuel system.

25893

25357

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands