MerCruiser QSD 2.0 Manual Download Page 71

Page: 71 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 63

Description

lb–in.

lb–ft

Fill and drain plug

6.8

–

16. Install the sterndrive propeller. See

Propellers

17. Recheck the gear lube level at the gear lube monitor after the first use. See

Checking

IMPORTANT: The gear lube level in the gear lube monitor will rise and fall during sterndrive operation; always check the gear

lube level when the sterndrive is cool and the engine is shut down.

Power Trim Fluid

Checking

IMPORTANT: Check the fluid level with the sterndrive in the full down (in) position only.
1. Place the sterndrive in full down (in) position.
2. Observe the fluid level. The fluid level must be between the "MIN" and "MAX" lines on the reservoir.

a -

Reservoir

b -

"MIN" and "MAX" lines

3. Fill as necessary with the specified fluid. See

Filling

Tube Ref No.

Description

Where Used

Part No.

114

Power Trim and Steering

Fluid

Power trim pump

92-858074K01

Filling

1. If the fluid level is below the "MIN" line, the specified fluid must be added.
2. Remove the fill cap from the reservoir.

NOTE: The fill cap is vented.

Power trim pump reservoir shows

the fluid level is below "MIN" line

a -

Fill cap assembly

b -

Fill cap installed

7876

7701

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands