MerCruiser QSD 2.0 Manual Download Page 60 | Manualshive

Page: 60 / 135

background image

Section 5 - Maintenance

Page 52

90-8M0057081

eng

MARCH 2011

2. Add the specified oil to bring the oil level up to, but not over, the maximum mark on the dipstick.

a -

Coolant oil cooler

b -

Seawater oil cooler

Engine Coolant Oil Cooler

QSD 2.0

System Capacity

Fluid Type

Part Number

Engine oil (with filter)

5.85 L (6.20 US qt)

15W40 4‑cycle Diesel Engine Oil

92‑877695K1

Engine Seawater Oil Cooler

QSD 2.0

System Capacity

Fluid Type

Part Number

Engine oil (with filter)

6.00 L (6.30 US qt)

15W40 4‑cycle Diesel Engine Oil

92‑877695K1

IMPORTANT: When refilling the engine with oil always use the dipstick to confirm the oil level.

3. Install the oil fill cap.

Changing Oil and Filter

See the

Maintenance Schedule

for the change interval. You should change the engine oil before placing the boat in storage.

IMPORTANT: Change the engine oil when the engine is warm from operation. Warm oil flows more freely, carrying away more

impurities. Use only recommended engine oil. See Specifications.
1. Start the engine and allow it to warm up to normal operating temperature.
2. Stop the engine and allow some time for the oil to drain into the oil pan (approximately five minutes).
3. Remove the fitting from the end of crankcase oil drain hose.
4. Install the crankcase oil pump (order separately) onto the threaded fitting of the engine oil drain hose.

Engine oil removal (Engine cover removed to

provide access)

a -

Engine oil drain hose

b -

Engine oil cap

c -

Crankcase oil pump

33988

a

b

25740

a

b

c

«
...
58
59
60
61
62
...
»

Summary of Contents for QSD 2.0








































































































































Reviews:

No comments

Related manuals for QSD 2.0

Brand: O.S. engine Pages: 5

MAX-15CV-R Series

Brand: O.S. engine Pages: 19

Brand: VEM Pages: 35

Brand: Saito Pages: 8

Brand: RHINO MOTION CONTROLS Pages: 4

Brand: MSW Pages: 159

GARDEN SNOWBUSTER (160F)

Brand: Texas Pages: 33

Brand: Grundfos Pages: 36

Brand: Interpump Pages: 16

Brand: Brother Pages: 76

Brand: Brother Pages: 112

Brand: Brother Pages: 22

Brand: Arrow Shark Pages: 16

Brand: Motion Pages: 92

Brand: Motion Pages: 124

Brand: New Holland Pages: 150

Brand: Continental Refrigerator Pages: 128

Brand: Stiga Pages: 232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands