MerCruiser QSD 2.0 Manual Download Page 109

Page: 109 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 101

Tighten the gimbal ring U‑bolt nuts to specification.

a -

Transom assembly

b -

Gimbal ring U‑bolt nuts

Description

lb–in.

lb–ft

Gimbal ring U‑bolt nuts for 3/8 in. U‑bolt

–

Gimbal ring U‑bolt nuts for 7/16 in. U‑bolt

–

Engine Mounts

Loosen the rear engine mount bolts 1 to 1‑1/2 turns. Retorque the rear engine mount bolts.

a -

Rear engine mount

b -

Transom plate mount

c -

Rear engine mount bolt

Description

lb. in.

lb. ft.

Rear engine mounts

Propellers

Alpha Propeller Removal

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat out of the water with a propeller installed. Before

installing or removing a propeller, place the drive unit in neutral and engage the lanyard stop switch to prevent the engine from

starting. Place a block of wood between the propeller blade and the anti‑ventilation plate.

1. Place wood block between propeller blade and anti‑ventilation plate to prevent rotation. Straighten bent tabs on tab washer.
2. Turn propeller shaft nut counterclockwise to remove nut.

19624

19622

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

MerCruiser QSD 2.0, Manual, Page: 109 / 135

Search results

Summary of Contents for QSD 2.0

Reviews: