MerCruiser Axius 350 Instruction Manual Download Page 87

Page: 87 / 149

Section 4 - Specifications

90-8M0053363

eng

NOVEMBER 2010

Page 79

Propshaft power

224 kW (300 hp)

Displacement

5.7 L (350 cid)

Alternator amperage

Hot

72 A

Cold

65 A

RPM

WOT

4800–5200

Rev limiter

5350

Idle in neutral

550

Minimum oil pressure

At 2000 RPM

124 kPa (18 psi)

At idle

41 kPa (6 psi)

Thermostat

Seawater‑cooled models

71° C (160° F)

MPI models with closed cooling

77° C (170° F)

Timing at idle

Not Adjustable

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Minimum battery rating

Non‑DTS models

750 CCA, 950 MCA, 180 Ah

DTS models

800 CCA, 1000 MCA, 190 Ah

Spark plug type

AC Platinum (AC 41‑993)

Spark plug gap

1.5 mm (0.060 in.)

Axius 377 MAG, Axius SeaCore 377 MAG with Emissions Control

NOTE: Performance specifications are obtained and corrected in accordance with SAE J1228/ISO 8665 Crankshaft Power.

All measurements are taken with the engine at normal operating temperature.

RPM range is measured using an accurate service tachometer with the engine at normal operating temperatures.

Oil pressure must be checked with the engine at normal operating temperature.
NOTE: Oil pressure specifications are for reference and may vary.

Propshaft power

293 kW (320 hp)

Displacement

6.2 L (377 cid)

Alternator amperage

Hot

72 A

Cold

65 A

RPM

WOT

4800–5200

Rev limiter

5350

Idle in neutral

550

Minimum oil pressure

At 2000 RPM

124 kPa (18 psi)

At idle

41 kPa (6 psi)

Thermostat

Seawater‑cooled models

71° C (160° F)

MPI models with closed cooling

77° C (170° F)

Timing at idle

Not Adjustable

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Minimum battery rating

Non‑DTS models

750 CCA, 950 MCA, 180 Ah

DTS models

800 CCA, 1000 MCA, 190 Ah

Spark plug type

AC Platinum (AC 41‑993)

Spark plug gap

1.5 mm (0.060 in.)

Fluid Specifications

IMPORTANT: All capacities are approximate fluid measures.

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands