MerCruiser Axius 350 Instruction Manual Download Page 86

Page: 86 / 149

Section 4 - Specifications

Page 78

90-8M0053363

eng

NOVEMBER 2010

Models

Axius and Axius SeaCore

350 MAG

Axius and Axius SeaCore

377 MAG

Power

224 kW (300 hp)

238 kW (320hp)

Number of cylinders

Displacement

5.7 L (350 cid)

6.2 L (377 cid)

Bore and Stroke

101.6 × 88.39 mm

(4.00 × 3.48 in.)

101.6 × 95.25 mm

(4.00 × 3.75 in.)

Compression ratio

9.4:1

9.0:1

Idle RPM in neutral

600

Specified WOT RPM range

4800–5200

Minimum oil pressure at idle

41 kPa (6 psi)

Thermostat (seawater‑cooled models)

71° C (160° F)

Thermostat (closed cooled models)

77° C (170° F)

Timing at idle

Not Adjustable

Firing order

1‑8‑4‑3‑6‑5‑7‑2

Electrical system

12‑Volt Negative (‑) Ground

Alternator rating

65 A

Recommended minimum battery rating

800 CCA, 1000 MCA, or 190 Ah

Spark plug type

AC Platinum (AC 41‑993)

Spark plug gap

1.5 mm (0.060 in.)

Engine Specifications

Axius 350 MAG, Axius SeaCore 350 MAG with Emissions Control

NOTE: Performance specifications are obtained and corrected in accordance with SAE J1228/ISO 8665 Crankshaft Power.

All measurements are taken with the engine at normal operating temperature.

RPM range is measured using an accurate service tachometer with the engine at normal operating temperatures.

Oil pressure must be checked with the engine at normal operating temperature.
NOTE: Oil pressure specifications are for reference and may vary.

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands