MerCruiser Axius 350 Instruction Manual Download Page 37

Page: 37 / 149

Section 2 - Getting to Know Your Power Package

90-8M0053363

eng

NOVEMBER 2010

Page 29

4. The power trim system is protected from overload by a 110 amp fuse and a 20 amp spade fuse on the power trim pump. The

trim pump may also have an in‑line circuit protection device in the power trim positive lead near the battery switch or battery

connection.

a -

20 amp spade fuse

b -

110 amp fuse

5. The electronic control unit of each engine has a separate power harness to minimize voltage drop. The power harness

connects to the engine starting battery and is protected by a 10 amp spade fuse in a fuse holder located near the battery.

Typical

a -

Cover

b -

10 amp spade fuse

c -

Fuse holder

6. The Quicksilver MerCathode system has a 20 amp in‑line fuse in the wire which connects to the positive (+) terminal on

controller. If the fuse is blown, the system will not operate resulting in a loss of corrosion protection.

mc79977

Warning Horn Signals

Most faults will cause the warning horn circuit to activate. How the warning horn activates depends on how serious the problem

is. There are four warning horn states:
•

Caution ‑ horn signal varies with product line and calibration. Minimal guardian.

•

Warning ‑ horn signal varies with product line and calibration.

•

Severe ‑ horn is beeping constantly.

•

Critical ‑ horn is beeping constantly and guardian will be at forced idle.

In addition, depending on the gauge package, there will be warning icons and fault messages on the dash mounted gauges.

9208

32206

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands