MerCruiser Axius 350 Instruction Manual Download Page 106

Page: 106 / 149

Section 5 - Maintenance

Page 98

90-8M0053363

eng

NOVEMBER 2010

Sterndrive Unit and Transom Assembly

1. Lubricate gimbal bearing by applying approximately 8‑10 pumps of grease from a typical hand‑operated grease gun.

a -

Gimbal bearing grease fitting

Tube Ref No.

Description

Where Used

Part No.

U-joint and Gimbal

Bearing Grease

Gimbal bearing

92-802870A1

2. For propeller shaft lubrication, refer to

Propellers

Sterndrive U‑joint Shaft Splines And O‑rings (Sterndrive Unit Removed)

1. Coat sterndrive U‑joint O‑rings and driveshaft splines with grease.

a -

Driveshaft splines

b -

U‑joint O‑rings (3)

Tube Ref No.

Description

Where Used

Part No.

Engine Coupler Spline

Grease

Driveshaft splines and U-joint O-rings

92-802869A 1

2. For propeller shaft lubrication, refer to Propellers.

Engine Coupler

1. Lubricate engine coupler splines through the grease fittings on the coupler by applying approximately 8–10 pumps of grease

from a typical hand‑operated grease gun.

mc77068-1

8591

Summary of Contents for Axius 350






















































































































































Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands

MerCruiser Axius 350, Instruction Manual

Search results

Summary of Contents for Axius 350

Reviews:

Related manuals for Axius 350

Brands by name

Popular brands