MerCruiser Axius 350 Instruction Manual Download Page 105 | Manualshive

Page: 105 / 149

background image

Section 5 - Maintenance

90-8M0053363

eng

NOVEMBER 2010

Page 97

9. Remove the filter cup from the filter cap by grasping the filter cap and rotating it in a clockwise direction while holding the filter

cup stationary.

10. Remove the used water‑separating fuel filter element from the filter cup, place it in a clean, approved container.
11. Dispose of any water or debris that may be in the filter cup.

Installation

1. Install a new water‑separating fuel filter element into the filter cup. Push the element into the cup until completely seated.
2. Install new O‑ring on the filter cup.
3. Attach the filter cap to the filter cup by grasping the filter cap and rotating it in a counter clockwise direction while holding the

filter cup stationary, until the filter cap locks securely into place.

4. Install the fuel filter assembly slowly into the Cool Fuel Module to prevent spilling fuel, and align the screws retained in the

filter cap with the screw holes in the Cool Fuel Module. Tighten the filter assembly retaining screws until hand tight.

5. Ensure that the filter cap is firmly seated against the Cool Fuel Module and torque each filter assembly retaining screw.

Description

Nm

lb. in.

lb. ft.

Filter assembly retaining screw

6

53

6. Open fuel supply valve, if equipped.
7. Reconnect the Cool Fuel Module harness to the engine wiring harness.
8. Properly ventilate the engine compartment.

NOTICE

Without sufficient cooling water, the engine, the water pump, and other components will overheat and suffer damage. Provide

a sufficient supply of water to the water inlets during operation.

9. Supply cooling water to the engine.
10. Start the engine. Check for gasoline leaks around the fuel filter assembly. If leaks exist, stop the engine immediately. Recheck

the filter installation, clean spilled fuel and properly ventilate the engine compartment. If leaks continue, stop engine

immediately and contact your authorized Mercury MerCruiser dealer.

Lubrication

Electronic Shift Control (ESC) Shift Cable

1. Lubricate the pivot points and the guide contact surfaces.

a -

Pivot points

b -

Shift actuator

c -

Guide contact surfaces

d -

Shift cable

Tube Ref. No.

Description

Where Used

Part No.

Synthetic Blend MerCruiser Engine Oil

SAE25W‑40

Shift cable pivot points &

guide contact surfaces

92‑883725K01

32233

c

a

d

b

«
...
103
104
105
106
107
...
»

Summary of Contents for Axius 350






















































































































































Reviews:

No comments

Related manuals for Axius 350

Brand: Rato Pages: 65

Brand: ACM Pages: 37

Brand: Schartec Pages: 16

Brand: Kohler Pages: 4

Brand: Daewoo Pages: 188

Brand: Dato Pages: 9

Brand: Yanmar Pages: 308

Brand: LONCIN Pages: 11

Brand: DLE Pages: 5

Brand: Vauth-Sagel Pages: 14

Brand: Honda Pages: 61

Brand: KAMA Pages: 25

DESMO TWINCAM 4V

Brand: Takegawa Pages: 19

Brand: Cuyuna Pages: 51

Brand: Zenoah Pages: 28

Brand: Jenny Science Pages: 9

Brand: ORION TELESCOPES & BINOCULARS Pages: 4

Brand: Omron Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands