X
Check the tire pressure on all four wheels
and correct it if necessary.
i
If the wheel positions on the vehicle are
interchanged, the tire pressures may be
displayed for the wrong positions for a
short time. This is rectified after a few
minutes of driving, and the tire pressures
are displayed for the correct positions.
Restarting the tire pressure monitor
It is the driver's responsibility to set the tire
pressure to the recommended cold tire
pressure. Underinflated tires affect the ability
to steer or brake the vehicle. You might lose
control over the vehicle.
When you restart the tire pressure monitor,
all existing warning messages are deleted and
the warning lamps go out. The monitor uses
the currently set tire pressures as the
reference values for monitoring.
The tire pressure monitor must be restarted
when you set the tire pressure to a new value
(as a result of changed drive or load
characteristics, for example). The tire
pressure monitor then monitors the new tire
pressure values.
Restart the tire pressure monitor after you
have set the tire pressure to the value
recommended for the desired driving
situation (
pressures on cold tires. Comply with the
recommended tire pressures on the tire and
loading information table on the B-pillar on
the driver's side. Additional tire pressure
values for driving at high speeds or with heavy
loads can be found in the tire pressure table
on the inside of the fuel filler flap.
X
Make sure that the tire pressure is correct
on all four wheels.
X
Make sure that the SmartKey is in position
2 in the ignition lock.
X
Press and hold the
V
or
U
button on
the multifunction steering wheel until the
standard display appears in the
multifunction display (
X
Press and hold the
&
or
*
button
until the tire pressure of each wheel or the
Tire pressure displayed after
driving for a few minutes
message
appears.
X
Press the reset button on the instrument
cluster (
The
Restart tire pressure
monitor?
message appears in the
multifunction display.
If you wish to confirm the restart:
X
Press the
W
button.
The
Tire Pressure Monitor
Restarted
message appears in the
multifunction display.
After driving for a few minutes, the system
checks whether the current tire pressures
are within the specified range. The new tire
pressures are then accepted as reference
values and monitored.
If you wish to cancel the restart:
X
Press the
X
button.
The tire pressure values stored at the last
restart will continue to be monitored.
Instruction labels for tires and loads
Do not overload the tires by exceeding the
specified load limit as indicated on the Tire
and Loading Information placard on the
driver's door B-pillar. Overloading the tires
can overheat them, possibly causing a
blowout. Overloading the tires can also result
in handling or steering problems, or brake
failure.
Loading the vehicle
333
Wheels and tires
Z
Summary of Contents for R 350 2012
