found on the reverse side of the remote
control).
The integrated garage door opener is
compatible with devices that can be
operated with units in a frequency range of
280 to 390 MHz.
R
change the batteries in garage door remote
control
A
. This increases the probability
that garage door remote control
A
will
send a strong and precise signal to the
integrated garage door opener on the rear-
view mirror.
R
when programming, hold garage door
remote control
A
at different distances
and angles from the transmitter button that
you are programming. Try different angles
at a distance between 2 and 12 inches (5
to 30 cm) or the same angle at varying
distances.
R
if another remote control for the same
garage door drive is available, repeat the
same programming steps with this remote
control. Before you perform the steps of the
operation, make sure that there are new
batteries in the garage door remote
control.
R
note that some remote controls only
transmit for a limited amount of time (the
indicator lamp on the remote control goes
out). Press the remote control button again
before it stops transmitting.
R
align the antenna cable of the garage door
opener unit. This can improve signal
reception/transmission.
Opening/closing the garage door
Once programmed, the integrated garage
door opener will assume the function of the
garage door system's remote control. Please
also read the operating instructions for the
garage door system.
X
Turn the SmartKey to position
2 in the
ignition lock.
X
Press transmitter button
;
,
=
or
?
in the
overhead control panel that you have
programmed to operate the garage door.
Garage door system with a fixed code:
indicator lamp
:
lights up green.
Garage door system with a rolling code:
indicator lamp
:
flashes green.
i
The transmitter will transmit a signal for
as long as the transmitter button is being
pressed. After a maximum of ten seconds,
transmission is terminated and indicator
lamp
:
flashes yellow. Press the
transmitter button again, if necessary.
Clearing the memory of the integrated
garage door opener on the rear-view
X
Turn the SmartKey to position
2 in the
ignition lock.
X
Press transmitter buttons
;
and
?
.
The indicator lamp lights up yellow.
X
Press and hold transmitter buttons
;
and
?
until the indicator lamp turns green.
i
Make sure that you clear the memory of
the integrated garage door opener before
selling the vehicle.
Whenever you are using a floormat, make sure
there is enough clearance and that the
floormat is securely fastened.
The floormat should always be securely
fastened using the fastening equipment.
Before driving off, check that the floormat is
securely in place and adjust it if necessary. A
loose floormat could slip and hinder proper
functioning of the pedals.
Do not place several floormats on top of each
other as this may impair pedal movement.
Features
405
Stowing and features
Z
Summary of Contents for CL2012
