manualshive.com logo in svg

mensor CPC4000, Operating Instructions Manual

Share
Download
mensor CPC4000 Operating Instructions Manual Download Page 43

Operating Instructions - CPC4000 

43

 

Industrial Pressure Controller

 CPC4000

6.4.3.3  Stability Parameters
Stability parameters for the controlled pressure can be found in the Control Settings App and can be 

configured using the Stable Window and Stable Delay buttons. When the controller enters a stable condi-

tion the pressure indication color on the Home App will change from white to green. The Stable Window 

button allows the user to enter a value as a percentage of the highest range transducer. This value repre-

sents the pressure window within which any setpoint value would be considered stable by the user. The 

Stable Delay button lets the user add a desired delay until the pressure value is considered stable while 

being in the stable window.

Stability  

Parameters

Figure 6.4.3.3 – Stability Parameters

6.4.3.4  Control Volume
The Control Volume button in the Control Settings App allows the user to control pressure volume in 

“cc”. The CPC4000 is capable of automatically identifying the control pressure volume and adjusting the 

control parameters based on it. By default this button is set on “Auto”. Figure 6.4.3.4 displays the control 

volume setting for the instrument.

 Figure 6.4.3.4 – Control Volume

Summary of Contents for CPC4000



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands