background image

 

42

 

MENDOTA EXTENDED LIFETIME PROTECTION AND LIMITED WARRANTY 

MENDOTA GAS FIREPLACE INSERT 

MODEL:  _____ NAT. & L.P. 

 

Mendota Division of Johnson Gas Appliance Company, 520 E Avenue N.W. Cedar Rapids, Iowa 52405, extends this Extended Lifetime Protection and 
Limited Warranty to the original purchaser of a Mendota Gas Fireplace Insert, Serial Number 

 

, which is limited and used under 

normal home conditions. 
 

STANDARD WARRANTY: 

 
JOHNSON GAS APPLIANCE CO., MENDOTA DIVISION, WARRANTS THAT YOUR NEW MENDOTA GAS FIREPLACE INSERT IS FREE 
FROM MANUFACTURING AND MATERIAL DEFECTS FOR A PERIOD OF ONE YEAR FROM THE DATE OF INSTALLATION, SUBJECT 
TO THE FOLLOWING CONDITIONS AND LIMITATIONS: 
 

EXTENDED LIFETIME WARRANTY: 

 
THE HEAT EXCHANGER, THE BURNER TUBE, THE COMBUSTION CHAMBER AND THE OUTER SHIELD OF THE MENDOTA GAS 
FIREPLACE INSERT ARE WARRANTED FOR THE LIFETIME OF THE ORIGINAL OWNER, SUBJECT TO PROOF OF PURCHASE AND 
THE FOLLOWING CONDITIONS AND LIMITATIONS: 
 
1) 

This new Mendota Fireplace Insert must be installed and serviced by a competent, authorized service contractor.  It must be installed and 

 

operated at all times in accordance with the installation and operating instructions furnished with the Fireplace.  All adjustments to logs, 

coals  

or burner must be made by an authorized Mendota Service person.  

 
This limited warranty does not cover the cost of service calls, the cost of labor to remove or install parts covered by this limited warranty, freight or 
other transportation expenses that may be incurred in connection with obtaining performances under this limited warranty.  The remedy for damages as 
the result of any defects in this product which have been warranted herein is limited to replacement parts and does not include any incidental, indirect 
or consequential damages or expenses sustained in connection with the products, including damages to property, except as provided by law. 
 
2) 

This warranty is non-transferable and is made to the original retail purchaser, provided the purchase was made through an authorized 

Mendota   dealer. 
 
Mendota is not responsible for any damage to or malfunction of the Insert unless caused by a defect in material or workmanship from normal home use.  
Damage caused by abuse, improper installation or operation, installation by unqualified personnel or breach of the conditions of this limited warranty 
will excuse Mendota from performance of any part of the limited warranty.   This warranty does not cover glass or log breakage. 
 
Mendota has the right to investigate and inspect the exact original fireplace and materials, in the event a claim is made (without alterations or 
tampering), to determine whether the claimed damage or malfunction was caused by abuse, improper installation or other cause outside this warranty.  
Mendota is not responsible for any repairs or material purchases that have not received prior written approval from Mendota. 
 
NOTE:  Minor warping of certain parts or discoloration is normal and is not a defect covered by this limited warranty.  Over-firing of your Mendota 
Fireplace Insert can cause major warping of parts.  Over-firing above rated nameplate specifications is contrary to the manufacturer's instructions and 
WILL void this warranty. 
This warranty may not be extended by our representatives in any manner.  The company neither assumes, nor authorizes any third party to assume, on 
its behalf, any other liabilities with respect to the sale of this Mendota product. 
 
3) 

Mendota may at its discretion, fully discharge all obligations of this warranty by refunding the wholesale price of the defective part(s). 

4) 

All other warranties - expressed or implied - with respect to the product, its components and accessories, or any obligation/liabilities on the 

part  

of the company are hereby expressly excluded.  Products made by other manufacturers, sold with the Fireplace or thereafter, are not covered 

by  

this limited warranty.  The use of unauthorized components will make this warranty null and void. 

 
This warranty shall be effective only if the original purchaser of the Mendota appliance is registered with Mendota Division within thirty (30) days of 
the date of purchase.  Such registration or the failure to register shall not be deemed to created any obligation or liability by the manufacturer and this 
warranty with its conditions and limitations shall be the only procedure for obtaining any rights against the manufacturer and expresses the sole 
obligation and responsibilities of the manufacturer which are offered to the original purchaser and accepted upon purchase of the appliance. 
 
Mendota Division, reserves the right to make changes at any time without notice, in design, material, specifications, prices and the right to discontinue 
styles and products. 
Some states do not allow the exclusions of limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so 
the above limitation or exclusion may not apply to you.  This warranty gives you specific legal rights and you may also have other rights, which vary 
from state to state.  

f i r e - p a r t s . c o m

Summary of Contents for SEABROOK D-40













































Reviews: