Mendota DXV35DT4 Assembly, Installation And Operating Instructions Download Page 1

85-03-01136 

ML39 

 

Installation and Operating Instructions 

MODEL NO. ML39 FULLVIEW DIRECT VENT GAS FIREPLACE HEATER 

 
 

 
 

WARNING:

 If the information in these instructions 

is not followed exactly, a fire or explosion may 
result causing property damage, personal injury or 
loss of life. 

 

AVERTISSEMENT

. Assurez-vous de bien suivre les 

instructions données dans cette notice pour réduire au 
minimum le risque d'incendie ou d'explosion ou pour 
éviter tout dommage matériel, toute blessure ou la mort. 

- Do not store or use gasoline or other flammable 
vapors and liquids in the vicinity of this or any other 
appliance. 
- WHAT TO DO IF YOU SMELL GAS 

Do not try to light any appliance. 

Do not touch any electrical switch; do not 
use any phone in your building. 

Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions. 

If you cannot reach your gas supplier, call 
the fire department. 

- Installation and service must be performed by a 
qualified installer, service agency or the gas 
supplier. 

Ne pas entreposer ni utiliser d'essence ni d'autres vapeurs 
ou liquids inflammables dans le voisinage de cet appareil 
ou de tout autre appareil.  
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:  

• Ne pas tenter d'allumer d'

appareil.  

• Ne touchez à aucun interrupteur. Ne pas vous servir des 

téléphones se trouvant dans le bâtiment où vous trouvez.  

• Appelez immédiatement votre fournisseur de gaz depuis 

un voisin. Suivez les instructions du fournisseur.  

• Si vous ne pouvez r

ejoindre le fournisseur de gaz, 

appelez le service des incendies.  
- L'installation et l'entretien doivent être assurés par un 
installateur ou un service d'entretien qualifié ou par le 
fournisseur de gaz.  
 

This appliance may be installed in an aftermarket, 
permanently located, manufactured home (USA 
only) or mobile home, where not prohibited by local 
codes. 
This appliance is only for use with the type of gas 
indicated on the rating plate. This appliance is not 
convertible for use with other gasses, unless a 
certified kit is used. 

 Cet appareil peut être installé dans une maison 
préfabriquée (É.-U. seulement) ou mobile déjà installée à 
demeure si les règlements locaux le permettent.  
Cet appareil doit être utilisé uniquement avec les types de 
gaz indiqués sur la plaque signalétique. Une trousse de 
conversion est fournie avec cet appareil. 

A barrier designed to reduce the risk of burns from 
the hot viewing glass is provided with this appliance 
and must be installed. 

 Une barrière conçue pour réduire le risque de brûlures 
du verre chaud est fournie avec cet appareil et doit être 
installée. 

Summary of Contents for DXV35DT4



























































































Reviews: