Memotec NetPerformer SDM-9120 Series Hardware Installation Manual Download Page 103

Page: 103 / 161

Product Description

Memotec Inc.

4-35

page 3-13

•

Framing and line coding:

T1: D4 or ESF framing and B8ZS, B7ZS or AMI line coding

E1: Provides G.704 framing and HDB3 line coding

•

Maximum 3 interface cards per unit, providing a maximum of 120 voice channels
or 124 data channels

NOTE:

Requires DSP resources for voice calls (see

“DSP Resources” on page 4-21

•

Interoperability with other channelized digital interface cards:

Can be installed and operated on a unit that has one or more single/dual port
T1/E1 or legacy E1 interface cards installed in the other slots.

Cannot

be installed on a unit that has one or more legacy T1 interface

cards installed in another slot.

Workaround:

Substitute a dual port T1/E1 interface card for the T1 interface,

and configure it for T1 operations.

Figure 4-27: Single-Port and Dual-Port T1/E1 Interface Cards

Dual-port
interface card

Single-port
interface card

Summary of Contents for NetPerformer SDM-9120 Series


































































































































































Search results

Summary of Contents for NetPerformer SDM-9120 Series

Reviews:

Brands by name

Popular brands

Memotec NetPerformer SDM-9120 Series, Hardware Installation Manual

Search results

Summary of Contents for NetPerformer SDM-9120 Series

Reviews:

Brands by name

Popular brands