Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 52

Page: 52 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 52 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

16 Installing the three-step rotary switch with zero

position

This section describes how to connect the three-step rotary switch with zero position elec-

trically to the ventilation unit.

WARNING

The activities described in this chapter must only be carried out by technicians with the

following qualifications:

— Training in the installation and commissioning of electrical devices

— Training in electrical hazards and the local safety requirements

— Knowledge of the relevant standards and directives

— Knowledge and observance of this document and all the safety instructions (see

chapter “2 Safety instructions” from page 12)

NOTICE

— The ventilation unit may be damaged if the control cable is connected incorrectly.

This will also invalidate the warranty.

— Also follow the installation manual for the M-WRG-II ventilation units (see

section 1.12 on page 11).

— The installation must be carried out in accordance with the generally acknowledged

rules of technology.

16.1

Switching off power to the ventilation unit

DANGER

Potentially fatal voltages

— The electrical installation work must only be carried out by a qualified electrician.

— The VDE regulations or any special safety regulations applicable in your country

apply to the electrical installation work.

► Before starting installation or maintenance work, disconnect the mains cable for

connecting to the ventilation unit on all poles from the mains supply.

► Observe the five safety rules (DIN VDE 0105-100, EN 50110-1) for working on elec-

trical systems:

— Disconnect from mains (all-pole disconnection of a system from live parts)

— Secure against reconnection

— Check that the system is voltage-free

— Earth and short-circuit

— Cover or block off access to adjacent live parts

Summary of Contents for M-WRG-II E-F





























































Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands

Meltem M-WRG-II E-F, Operating And Installation Instructions

Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands