Meltem M-WRG-II E-F Operating And Installation Instructions Download Page 26

Page: 26 / 60

Operating and installation instructions

M-WRG-II P-T (-F, -FC), M-WRG-II E-T (-F, -FC) ventilation units

- 26 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L A T I O N & H E A T R E C O V E R Y

7.2

Controls and indicators on the InControl pushbutton sensor

The InControl pushbutton sensor allows you to select one of six different ventilation

programs. The available ventilation programs depend on the type of ventilation unit.

Every button has an LED that indicates the currently selected ventilation program.

7.2.1 InControl pushbutton sensor for type M-WRG-II P-T and

M-WRG-II E-T ventilation units

Reduced

ventilation

(people absent) /

Standby mode

Increased ventilation

Supply air operation

(Summer mode)

Normal

ventilation

(people present)

Intensive ventilation

(15 min)

Extract air operation

Fig. 14: InControl pushbutton sensor for M-WRG-II P-T

and M-WRG-II E-T

7.2.2 InControl pushbutton sensor for type M-WRG-II P-T-F and

M-WRG-II E-T-F ventilation units

Reduced

ventilation

(people absent) /

Standby mode

Increased ventilation

Humidity control

Normal

ventilation

(people present)

Intensive ventilation

(15 min)

Supply air operation

(Summer mode)

Fig. 15: InControl pushbutton sensor for

M-WRG-II P-T-F and M-WRG-II E-T-F

Summary of Contents for M-WRG-II E-F





























































Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands

Meltem M-WRG-II E-F, Operating And Installation Instructions

Search results

Summary of Contents for M-WRG-II E-F

Reviews:

Related manuals for M-WRG-II E-F

Brands by name

Popular brands