manualshive.com logo in svg

Meltem M-WRG-ES, Installation Manual, Page: 10 / 24

Share
Download
Meltem M-WRG-ES Installation Manual Download Page 10

Installation manual 

Outer wall terminals M-WRG-ES, M-WRG-ESR, M-WRG-ESG

- 10 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N   &   H E AT   R E C O V E R Y

3.3 

Items supplied with the outer wall terminal stainless steel, louvred design 

M-WRG-ESG

Fig. 6:  Items supplied with the outer wall terminal stainless steel, louvred design

Item Description

Quantity

1

Outer wall terminal stainless steel, louvred design, surface-mount 

(M-WRG-ESG/AP or M-WRG-ESG/AP-P only, section 1.2.3, page 4)

1x

2

Outer wall terminal stainless steel, louvred design, flush-mount 

(M-WRG-ESG/UP or M-WRG-ESG/UP-P only, section 1.2.3, page 4)

1x

3

Drilling template

1x

4

Vaseline, tube

1x

5

Dowel 6 x 30 mm for fitting to brick wall

6x

6

Screws 4.0 x 40 mm, stainless steel

6x

-

Installation manual

1x

NOTE

The fixing materials supplied are intended for fixing the outer wall terminal to brick walls.

 

►

For other wall structures, contact your facade constructor to ensure that the outer wall termi-

nals are fitted correctly.

NOTE

Würth insulation anchors with setting tool, part no. 090350050, for example, are suitable for fixing 

the outer wall terminals to rigid foam boards.

Summary of Contents for M-WRG-ES

























Reviews:

No comments