Mellanox Technologies Grid Director 4700 Installation Manual Download Page 87 | Manualshive

Page: 87 / 88

background image

Mellanox Grid Director 4700 Installation Manual

87

QSFP Cable Overview

Every 4700 port on the switch is equipped with transmit and receive circuits that can adjust to
fit different types of link characteristics and either optical or copper cables.

The QSFP cables transmit and receive up to 10 Gbps per channel (total: up to 40 Gbps per
port) over a single active/passive optical or copper cable, Passive copper cables do not
consume any additional power while active copper and optic cables consume up to 2.5 Watt.

You can use the QSFP module with Copper or Optical cables. You can install any combination
of the cables in any of the QSFP cages.

A.2

IB Port Cable Specifications

The following table details the cabling specifications for the 4036E 4X InfiniBand ports.

Table 33: 4X InfiniBand Port Cabling Specifications

Type

Maximum Cable Length

4XQDR

AWG

Length (ft.)

Length (m)

Mellanox P/N

26

22.96

7

CBL-00158

26

16.4

5

CBL-00086

30

9.84

3

CBL-00185

30

6.57

2

CBL-00084

30

3.28

1

CBL-00083

30

1.64

0.5

CBL-00113

4XQDR –
4036E/HCA

26

26.25

8

CBL-00157

26

22.96

7

CBL-00158

26

16.4

5

CBL-00086

30

9.84

3

CBL-00185

30

6.57

2

CBL-00084

30

3.28

1

CBL-00083

30

1.64

0.5

CBL-00113

Type

Maximum Cable Length

4XQDR

Length (ft.)

Length (m)

Mellanox P/N

9.84

3

New PN (Finisar)

16.4

5

New PN (Finisar)

32.8

10

CBL-00102

49.2

15

CBL-00103

65.6

20

CBL-00104

«
...
85
86
87
88
»

Summary of Contents for Grid Director 4700

























































































Reviews:

No comments

Related manuals for Grid Director 4700

Switch 4500 Family

Brand: 3Com Pages: 16

PathBuilder S200 Series

Brand: 3Com Pages: 32

Brand: Hama Pages: 14

Super Speed USB 3.0 Hub

Brand: Hama Pages: 14

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Premium Silver USB 2.0 Hub 1:4

Brand: Hama Pages: 12

Brand: Hama Pages: 18

uRage Vendetta 210

Brand: Hama Pages: 36

Brand: IBM Pages: 166

Brand: BERNSTEIN Pages: 3

Brand: socomec Pages: 78

Brand: Delta Electronics Pages: 1

Brand: Grizzly Pages: 2

Brand: Festo Pages: 2

Brand: Hanwell Pages: 109

Brand: Olympia Pages: 6

tekmarNet4 User Switch 480

Brand: Tekmar Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands