Mellanox Technologies Grid Director 4700 Installation Manual Download Page 22

Page: 22 / 88

System Configurations

The following figure illustrates the Grid Director 4700 with HyperScale Fabric Board (spine)
InfiniBand internal switching topology.

Figure 6: Grid Director 4700 HyperScale Spine Switching Topology

The Grid Director 4700 topology feature eighteen symmetrical Line Boards (sLB) and nine
interconnect Fabric Boards (sFB).



Each Line Board (sLB-4018) includes one 36-port 40Gb/s InfiniBand switch chip.



Each Fabric Board (sFB-4700) includes one 36-port 40Gb/s InfiniBand switch chip.



Each HyperScale Fabric Board (sFB-4700-2X) includes two 36-port 40Gb/s InfiniBand
switch chips.

The LEDs on the Fabric Board modules indicate proper connectivity and traffic flow between
each line board and the respective fabric board.

Summary of Contents for Grid Director 4700

























































































Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands

Mellanox Technologies Grid Director 4700, Installation Manual

Search results

Summary of Contents for Grid Director 4700

Reviews:

Related manuals for Grid Director 4700

Brands by name

Popular brands