manualshive.com logo in svg

Meler Micron PUR LC, Instruction Manual

Share
Download
Meler Micron PUR LC Instruction Manual Download Page 64

MELER GLUING SOLUTIONS

4-30

MELTER OPERATION

ENGRANE

HMI 

: S02001100 v1.0.106

TC  

: S02200100 v1.0.084

IO  

: S02102100 v1.0.106

IO  

: S02101100 v1.0.106

30 s

50 rpm

30 s

50 rpm

5. Pumping

Manual Control Pump 1

PLAY

Manual Control Pump 2

PLAY

Menu ‘5. Pumping’

To can configure the following options separately for each pump:

•  Manual control pump 1 or 2:

 If ‘Manual control’ is activated, pumping 

can be activated or stopped by pressing ACTIVATE (with the unit in 

Temperature OK).  

 

The button changes from STOP to ACTIVATE every time it is pressed. 

A maximum number of RPM and maximum pumping time can be 

programmed, after which the unit stops manual pumping.

ENGRANE

HMI 

: S02001100 v1.0.106

TC  

: S02200100 v1.0.084

IO  

: S02102100 v1.0.106

IO  

: S02101100 v1.0.106

90 rmp

30 s

10 rpm

min

max

85 rmp

35 s

15 rpm

min

max

Pump 1 speed alarm

5. Pumping

Pump 2 speed alarm

•  Speed alarm pump 1 or 2:

 If this is activated, the unit will activate an 

alarm if the speed of the pump does not remain within the minimum and 

maximum speed range during the set time.

Summary of Contents for Micron PUR LC











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands