manualshive.com logo in svg

Meler Micron PUR LC, Instruction Manual

Share
Download
Meler Micron PUR LC Instruction Manual Download Page 61

MELTER OPERATION

4-27

MA-5184-ENG 

  PUR LC/MC ADHESIVE MELTER

ENGRANE

HMI 

: S02001100 v1.0.106

TC  

: S02200100 v1.0.084

IO  

: S02102100 v1.0.106

IO  

: S02101100 v1.0.106

DI1

DI2

DI3

DO2

DO3

DO4

2.3 Input / Output

Imput

Output

Standby

COMs OFF

Pump OFF

Temperature OK

Alarms

Adhesive Level

ENGRANE

HMI 

: S02001100 v1.0.106

TC  

: S02200100 v1.0.084

IO  

: S02102100 v1.0.106

IO  

: S02101100 v1.0.106

Are you sure  

you want to restore  

to the default settings??

YES

NO

2.3 Configuration of input and output signals

This allows you to configure the unit’s digital input and output signals. 

The inputs can be:

•  ON/OFF: 

Switches the unit fully off or on.

•  Standby: 

Activates or deactivates the Standby mode.

•  Activity: 

Enables the activity control to measure the times for switching 

automatically to Standby and OFF.

•  Pumping: 

Activates or deactivates the pumping.

•  COMM.: 

Activates or deactivates the communications.

The outputs can be:

•  Standby: 

Indicates that the unit is in Standby mode.

•  Zones in Temperature OK. 

Indicates that all active zones are in tempera-

ture OK.

•  Ready. 

Indicates that the unit is ready to operate, with temperature OK 

and no operating errors.

•  Running. 

The unit is pumping, with temperature OK and no operating 

errors.

•  Alarm:

 Indicates that there is an active Alarm.

 

•  Level: 

Indicates high level of adhesive in the tank.

•  No Level: 

Indicates low level of adhesive in the tank.

2.4 Restore default values

Allows you to delete all the changes made to the system and leave the unit 

with the factory-set default parameters. After pressing, the following confir-

mation message will appear. 

When you press ‘YES’, the device restarts with the default configuration.

Summary of Contents for Micron PUR LC











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands