Megger DELTA4000 Instruction Manual Download Page 42 | Manualshive

Page: 42 / 74

Megger DELTA4000 Instruction Manual Download Page 42

M

AVTMDELTA4000-EN Rev 6 April 2018

34

Start and Stop

When you are ready to start measuring, press the Start button. In all modes
except the Manual type, the measurement sequence is automatic and the result

presented when finished. If you need to stop an ongoing measurement press the

Stop button. Note: the Stop button stops the measurement smoothly, if stop by

emergency reason, simply release the interlock in the interlock handle.

Note:

The green light on the start button will not illuminate until both

interlock switches are closed.

In manual mode you have a button for starting a measurement. The start button
is used to activate the output. You can manually control output voltage using the

Voltage control. You can record and store a value to the log at any time by

pressing the Measure button.

Press Stop or "Esc" to stop the output voltage.

Oscilloscope

In the oscilloscope you can follow applied voltage (red) and a voltage

proportional to measured current (white).

Note:

This feature is designed to be a signal monitor and not intended to be a
measurement device. The display has auto scaling of amplitude and time

axis.

Results

«
...
40
41
42
43
44
...
»

Summary of Contents for DELTA4000











































































Reviews:

No comments