manualshive.com logo in svg

Megger DELTA4000, Instruction Manual, Page: 25 / 74

Share
Download
Megger DELTA4000 Instruction Manual Download Page 25

Controls, Indicators, and Connectors 

 

 

AVTMDELTA4000-EN Rev 6 April 2018 

17 

 

STROBE 

Receptacle for connecting the warning strobe 

light 

 

TEMP and %RH 

Receptacle for connecting the temp and humidity 

sensor (optional accessory) 

 

INDUCTOR 

Receptacle for connecting the test set to an 

optional Resonating Inductor (Cat. No. 670600-
1) for extended capacitance range. 

 

HV CONTROL 

Receptacle for the control cable between the 
control and HV units 

 

MAINS 

Receptacle for connecting the test set to an AC 

power source as marked on panel. 

 

TEST GROUND 

Receptacle for connecting the test ground cable 

between the test set and ground (normally station 

ground) near the test object 

 

GROUND 

This wing nut is for connecting an additional 

safety ground between the control and HV units 
or to ground external objects e.g. optional trolley 

 

HV POWER 

Receptacle for the power cable between the 

control and HV units  

 

 

 

Summary of Contents for DELTA4000











































































Reviews:

No comments