®
CONTROLLER MANUAL
H-60P
All products, controllers, specifications and data as well as a set of items packaged in a box are subject to change without notice to improve reliability, function or design of the devices.
Please, check for the most updated products details at
www.MediCrystal.com
web site.
H-SERIES CONTROLLER FEATURES
A HIGHLY DEVELOPED I.C CHIP WHICH CUTS OFF
HARMFUL ELECTROMAGNETIC WAVES.
Always remember to turn off the electrical
supply when not in use. When unplugging
device, do not attempt to pull the cord, pull
it out by holding the plug.
Remember that it is very important to consult your doctor before use and always properly hydrate with pure and mineralized water before and aſter sessions with
the mat. Begin with low temperatures and short procedures and use a slow and continuous mode of increasing sessions intensity, duration and frequency. It is
important to feel comfortable and enjoy your experience, so listen to your body and adjust procedures accordingly.
• First
tightly connect controller to the mat connector
. Ensure the
controller’s mat plug is pushed all the way into the mat’s receptacle
socket so that it is snug tight with no space at all between the plug and
the mat’s socket. Then plug-in controller into the power outlet and turn
ON controller with toggle button
.
•
If you connect controller to the power source first, the safety program
may lock it. It may start to beep or show
OF
or
OP
errors. A loose
connection can also cause loss of signal exchange between the mat and
the controller and controller errors. Display
may show
OF
when preset
heating time is over.
Try adding time, power the controller ON/OFF, or
reset controller reconnecting it to the mat in correct order.
•
Disconnect the plug from the socket first and then from the mat
connection terminal.
When you disconnect, first turn controller OFF, then
disconnect the plug from the socket, and only aſter this unplug the
controller from the mat. Please always do it carefully with two hands,
holding the connector with one hand while the other hand pulls the plug out
of the connector on the mat.
Reconnection and reset are the most common ways to eliminate errors
and reload the controller. But if reconnection or any other way of
troubleshooting do not improve the situation, it likely means that
there is a problem with the controller. If your controller was not
accidentally damaged or flooded and is under warranty, we replace it
ASAP, fast and free. Please, contact us at
•
Sometimes controllers issues happen aſter power spikes. When
hurricanes or storms are approaching, if you are not going to use your
mat for a while, or if you are leaving your home for a weekend or vacation
it is better to unplug the mat from the socket.
The best is to keep the
mat unplugged from the power socket always while it is not in use
. No
need to unplug the controller connector from the mat connection terminal
frequently. If the controller always remains connected to the mat it is OK
as this only helps prevent the connection from loosening. Just remember
to verify the tightness of the connections from time to time, especially if
you sleep on your mat.
•
The mat controller has four times settings 1 hour, 4 hours, 8 hours and
12 hours. You should choose one fo them first to activate heating. Aſter you
turn ON controller press timer button
to adjust time setting.
•
Controller has a temperature dial
to adjust the heat in 1 °C
increments from 86 °F to 158 °F, displayed in Celsius from 30 °C to
70 °C.
The temperatures reflect condition of the inner heating
elements, not the surface of the mat, which can be 10-20 °C lower
.
Most of the energy from the hot crystals, in the form of Far Infrared Rays
heat, is transferred by radiation, and not by conduction. The mat should
be slightly warm on lower levels, warm on medium levels and very warm
on high levels. If the ambient temperature is around 70 °F, it takes
between a half an hour to hour for the mat to reach the maximum level if
covered it with a thick blanket.
•
Some of MediCrystal® controllers may feature a safety system
protecting users from overheating and dehydration
. When temperature
is set above 122 °F (50 °C) for longer than 3.5 hours, auto protection
feature will decrease it to safe 113 °F (45 °C) level.
•
If it is not comfortable for you and you need to use the mat on
higher temperature than 122 °F (50 °C) for longer than 3.5 hours,
you can manually inactivate it. Press and hold Timer Control Button
for 5 seconds until display shows
S-
. Press and hold Timer Control
Button
for 5 seconds until display shows
SA
to reactivate auto
protection feature.
•
If your controller
does not have this system
, be sure to use only the
lowest heat setting when sleeping on the mat or if you use the mat in the
evening when you may relax and fall asleep. Use an extra plug-in timer
(not included) for double safety.
HOW TO USE AND TROUBLESHOOTING
Сontrollers do not have a light indicating when negative ions are being generated, but you can be assured that the negative ions are being created by the special layers
of your device, always, when the controller is ON, and even for a while after turning it off.
for WRAP with PHOTON / CONNECTOR type B (5 pins) / VOLTAGE 110-120V 60Hz
Do not use in 220-250V
countries without a step
down power converter
transforming
220-240V to 110-120V
Never use
controller
with travel plug
or adapter!
Be sure that connection is
snug tight with no space at
all between the plug and
the mat’s socket.
Information provided hereby is for reference purposes only
and is not intended to recommend our devices as a drug or
as a diagnosis for any illness or disease condition; nor as a
product to eliminate disease or other medical condition and
is not a substitute for professional medical advice.
MediCrystal LLC does not make any medical claims, real or
implied, as to benefit of our products, devices and methods.
No MediCrystal® products or statements have been evaluated
by the FDA, nor has the FDA approved these products to
diagnose, cure, or prevent disease in humans or in pets. FDA
registration of devices manufacturer does not mean that the
device is intended for medical use, treatment of cancer or
any other diseases or medical conditions, or can be a
replacement of doctor's advice or traditional medical care
and therapy. There are contraindications and it is your
responsibility to consult health professional prior to use of
MediCrystal® products. Specific medical advice should be
obtained only from a licensed health care professional. These
and all other MediCrystal® products are non-medical,
non-medicinal devices and are not intended to diagnose,
treat, or prevent any disease or condition. All MediCrystal®
products are marketed for consumer home use and the
customer holds ultimate responsibility for any use of the
device or information and for all consequences.
LEGAL DISCLAIMER
