Mediatrix 4102S Hardware Installation Manual Download Page 3

Install the Mediatrix unit in a well-ventilated location where it will not be exposed to high temperatures or humidity.

Storage temperature: -20ºC to +70ºC
Operating temperature: 0ºC to +40ºC
Humidity lower than 85% and non-condensing

Do not install the Mediatrix unit in a location exposed to direct sunlight or near stoves or radiators. Excessive heat could damage the internal 
components.
Unit should be positioned to be accessible for future upgrade, maintenance and troubleshooting and where cables can be easily connected.
Maintain a minimum of 25 mm (1 in.) clearance in front, in the back, on top, and on the sides of the unit.
Keep airflow around and through the vents of the unit clear of any obstruction.
Do not put books or paper on the unit.

Top

Wiring Guidelines

These guidelines apply for any cable, supplied or not, used with a Mediatrix unit.

Always use straight through cables.
Cables must not pull or create a lateral stress on the connectors, i.e. they must be long enough.
Cables must be installed in such a way not to present a trip hazard to personnel working in the vicinity of the equipment.
Keep cables away from:

Sources of electrical noise such as radios, transmitters, and broadband amplifiers
Power lines
Fluorescent lighting fixtures
Liquids or moisture
Heat sources

Top

Mediatrix 4102S Characteristics

Parameter

Description

Dimensions

Height: 4.9 cm (1.9 in.)
Width: 22 cm (8.7 in.)
Depth: 17.6 cm (6.9 
in.)

Weight

458g (1.0 lb)

Power consumption

100 Vac -240 Vac
50 Hz / 60 Hz 2A

Top

Getting Started

Installation Check List

Task

Verified by Date

Network information available and recorded in site log.
Location requirements verified.
Site power Voltage.
Installation site pre-power check completed.
Mounting tools and equipment available.
Additional equipment available.
Mediatrix unit received.
Regulatory compliance and safety information received.
Software version verified
Rack, desktop mounting of chassis completed.
Initial electrical connections established.
Cable length limits verified.
Initial configuration performed.
Initial operation verified.

Top

Package Check List

Item

Condition

1 Mediatrix unit
1 external Power Adaptor with a cord for the country in which you are using the Mediatrix Unit
1 Printed flyer
1 Bumpon kit for desktop use

Top

Summary of Contents for 4102S














Reviews: