Media5 Mediatrix 4104 Reference Manual Download Page 402 | Manualshive

Page: 402 / 466

background image

Appendix C - Cabling Considerations

RJ-45 Cable

380

Mediatrix 4104

The RJ-45 cable uses two pairs of wires: one pair for transmission and the second pair for reception. It is wired
so that pins 1 & 2 are on one twisted pair and pins 3 & 6 are on a second pair according to common wiring
standards which meet the EIA/TIA T568A and T568B requirements.

Figure 92:

Straight Through Connectivity

Pin Name And Function

The following is the meaning of each pin in a RJ-45 cable.

Crossover Cable

A RJ-45 crossover cable is used when only two systems are to be connected to each other, peer to peer, at
the Ethernet Cards by “crossing over” (reversing) their respective pin contacts. An example would be
connecting two computers together to create a network. The crossover eliminates the need for a hub when
connecting two computers. A crossover cable may also be required when connecting a hub to a hub, or a
transceiver to transceiver or repeater to repeater. When connecting a hub to a transceiver, a straight through
cable is always used.

A crossover cable is sometimes called a null modem. The coloured wires at either end are put into different
pin numbers, or crossed over.

Figure 93:

Crossover Connectivity

Table 240:

Pin Name and Function

Pin #

Name

Function

1

Transmit Data Plus

The positive signal for the TD differential pair. This signal contains the serial
output data stream transmitted onto the network.

2

Transmit Data Minus

The negative signal for the TD differential pair. This contains the same
output as pin 1.

3

Receive Data Plus

The positive signal for the RD differential pair. This signal contains the serial
input data stream received from the network.

4

not connected

5

not connected

6

Receive data minus

The negative signal for the RD differential pair. This signal contains the
same input as pin 3.

7

not connected

8

not connected

Pin 1

Pin 2

Pin 3

Pin 6

Pin 1

Pin 2

Pin 3

Pin 6

Note:

This is not an IEEE supported configuration and should be used for test purposes only.

1- TX+

2- TX-

3- RC+

6- RC-

TX+ -1

TX- -2

RC+ -3

RC- -6

«
...
400
401
402
403
404
...
»

Summary of Contents for Mediatrix 4104



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Mediatrix 4104

Brand: Vigor Pages: 6

Brand: Linksys Pages: 2

Brand: Belkin Pages: 18

PV-KBT4 UR Series

Brand: Staubli Pages: 12

Brand: Addonics Technologies Pages: 4

Brand: Nvidia Pages: 62

NOVA Comet Versaturn

Brand: Teknatool Pages: 16

Brand: Micro Connect Pages: 5

Brand: Titan Electronics Pages: 76

Brand: l-com Pages: 54

Brand: Emulex Pages: 19

PCIe to ExpressCard Adapter

Brand: SIIG Pages: 8

Brand: Intermec Pages: 174

XE602 - Powerline Ethernet Adapter

Brand: NETGEAR Pages: 18

CURV 500 Series

Brand: LD Pages: 24

Brand: SWEEX Pages: 4

horNET Wi-Fi PCI 11g

Brand: Pentagram Pages: 28

FittingLINK 3.0

Brand: oticon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands