Meade 608007 User Manual Download Page 1

WARNING!

Never use the Meade cell phone holder or cell phone camera to look 

at or image the Sun! Looking at or near the Sun will cause instant 

and irreversible damage to your eye. Eye damage is often painless, 

so there is no warning to the observer that damage has occurred un-

til it is too late. Never attempt to image the sun with your cell phone 

camera as it will damage the camera permanently. Do not point the 

telescope at or near the Sun. Children should always have adult su-

pervision while observing.

INTRODUCTION

Your Meade telescope cell phone holder will allow you to take pictures 

through the telescope. This is ideal for taking images of the Moon, 

planets, and other bright object like star clusters. To use your telescope 

cell phone holder, read through the entire instructions first, then follow 

the steps below. Damage to your cell phone can occur with improper 

use.

FEATURES

Meade’s telescope cell phone holder is compatible with many cell phone 

types and sizes. Its design includes several adjustments that allow 

for correct postitioning of the phones camera into the optical path of 

the telescope. These features and adjustments as shown in Fig 1 are 

referenced below. 

INSTALLING THE PHONE INTO THE HOLDER

To begin, first loosen each of the phone holder knobs and adjustments 

and become familar with the way it moves and operates. This will make 

postioning your cellphone in the proper location easier. When installing 

the cellphone take care and verify you have locked the phone securely 

into the holder, or damage to your phone can occur if it falls from the 

holder. Follow the below steps to secure your cellphone into the holder.

Note: Item #’s in parenthesis(#) refer to the parts in Figure 1.

1.  Loosen the Phone Holder Bracket Lock Knob (#2) and rotate the 

Phone Bracket Holder Bracket (#1) so it is perpendicular to the 

Vertical Stage (#3) as shown in Figure 1.

2.  Expand the Phone Holder Bracket (#1) and place your cell phone 

into the bracket with the camera sensor facing downward and 

inward toward the Camera Centering Position (#7). The phones 

display should be facing upward.  If the phone is too large or has 

an awkward case, remove the case and try again.

3.  With the phone in position, squeeze the clamp closed making sure 

the bottom of the phone is in full contact with the phone bracket 

floor. Position the phone so the clamp  is midway along the phone. 

The phone body should remain parallel with the Vertical Stage (#3) 

as shown in Figure 2 & 4.

4.  Tighten the Phone Holder Bracket Lock Knob (#2) slightly and 

move the Phone Holder Bracket (#1) toward or away from the 

Camera Centering Position (#7) until the phone camera sensor is 

precisely centered in the Camera Centering Position(#7). Carefully 

flip  over  the  phone  bracket  and  check  the  camera  centering  as 

shown in Figure 3.

5.  Securely tighten the Phone Holder Bracket Lock Knob (#2) so the 

phone does not fall out of the holder and camera remains centered 

in centering position (#7).

6.  Now adjust the vertical position by loosening the Vertical Stage 

Lock Knob (#4). Raise or lower the Vertical Stage (#3) so the 

camera sensor does not interfere with the phone holder. See 

Figure 4. The camera should remain parallel to the mounting 

bracket for best performance.

ATTACHING THE PHONE HOLDER TO THE EYEPIECE

To attach the phone holder to the included 20mm eyepiece, you must 

remove the flip-up rubber eyecup located at the top of the eyepiece. 

1.  Carefully pull up on the rubber eyecup to remove it. Be sure to 

store the eyecup in a safe place as you can reinstall it again later 

if desired. The rubber eyecup will help block out stray light when 

using the eyepiece visually.

Meade Instruments

Cell Phone Holder 

Users Guide

Fig. 2 

1.  Phone Holder Bracket
2.  Phone Holder Bracket Lock 

Knob

3.  Vertical Stage
4.  Vertical Stage Lock Knob

5.  Eyepiece Locking Thumb-

screws (3)

6.  Eyepiece mounting 
7.  Camera Centering Position

Fig. 1 

1

2

3

4

5

6

5

(Not Visible)

7

Bottom side of phone holder

Cell 

Phone

Camera 

Sensor

Eyepiece 

Locking 

Thumbscrew

Eyepiece 

Mounting 

(Fig 1,#6)

Fig. 3

Phone installed on holder

Reviews: