MDT Technologies SCN-IP000.03 Technical Manual Download Page 19 | Manualshive

Page: 19 / 57

background image

Technical Manual – IP Router SCN-IP100.03

MDT technologies GmbH •

51766 Engelskirchen • Papiermühle 1

Tel.: +49-2263-

880 • Fax: +49-2263-4588 • [email protected] • www.mdt.de

19

19

3.5 Advanced security mechanisms

In addition to the use of KNX IP Secure, the following guidelines should be taken into account during
planning:



Do not allow any ports of routers to access the Internet



Secure LAN/WLAN system via a firewall



If no external access to the KNX installation is required, the default gateway can be set to the
value 0. This prevents communication to the Internet.



Access to the KNX installation from the Internet should be realised via a VPN connection

3.6 Requirements for KNX IP Secure/Data Secure

ETS 5.7.2

is required for commissioning Data Secure/IP Secure.

«
...
17
18
19
20
21
...
»

Summary of Contents for SCN-IP000.03


























































Reviews:

No comments

Related manuals for SCN-IP000.03

Brand: Lanpro Pages: 5

8BIG RACK THUNDERBOLT 2

Brand: LaCie Pages: 28

Brand: T&D Pages: 122

HomePlug AV Ethernet Bridge PLE0200

Brand: Abocom Pages: 2

Brand: axing Pages: 52

Media Board D/120JCT-LS-EW

Brand: Dialogic Pages: 2

Brand: Lanner Pages: 38

Brand: Allied Telesis Pages: 34

ISDN SOHO Router

Brand: AOpen Pages: 89

Brand: 3Com Pages: 12

Brand: LevelOne Pages: 3

Brand: LevelOne Pages: 4

Brand: Linksys Pages: 2

Brand: Trend Micro Pages: 2

Brand: ZyXEL Communications Pages: 12

Brand: R3 Pages: 48

Brand: H3C Pages: 4

Brand: RadioLabs Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands