© 2014 MDM INC.
Corrosion-resistant, non-metallic pumps.
© 2014 MDM INC.
Corrosion-resistant, non-metallic pumps.
Proudly Made in the USA
Proudly Made in the USA
INSTALLATION AND SERVICE MANUAL
WARNING:
Please read completely before you install or operate your new pump! This is an external “out-of-pond” pump!
It is NOT submersible! Do NOT allow this pump to become submerged! Never run dry! Max. case pressure.- 65 PSI!
4000
4000
S/N: XXXX-XXXXXX
XXXXXXXXX
TYPE:
END-SUCTION CENTRIFUGAL
MOTOR:
NEMA C FACE, 56J
PORT SIZE:
2” FNPT AND BUTTRESS THREAD PORTS -
INLET & DISCHARGE
HORSEPOWER:
1/8 HP THROUGH 5 HP
MATERIAL:
30% GLASS-FILLED NORYL® IMPELLER
40% GLASS-FILLED POLYPROPYLENE -
BRACKET AND VOLUTE
HARDWARE:
STAINLESS STEEL
SEAL OPTIONS:
STAINLESS STEEL WITH VARIOUS
ELASTOMERS, NON-METALLIC IMPENATRA® SEAL
WITH MULTIPLE CONFIGURATIONS FOR CHEMICAL
COMPATIBILITY.
OTHER OPTIONS:
EXTENSION COUPLED, PEDESTAL MOUNTED AND LONG
COUPLED WITH PEDESTAL MOUNTED PUMP ON FIBER-
GLASS BASEPLATE. PUMP ENDS ALSO AVAILABLE.
WARNING: EYE PROTECTION IS STRONGLY RECOMMENDED
MAINTENANCE
*The pump must be drained before servicing or if stored below freezing temperatures. Periodic replacement of seals may be required due to normal carbon wear.
Lubrication
Motor - Permanently Lubricated ball bearings - no service required.
Rotary Seal - Requires no lubrication after assembly.
TROUBLE SHOOTING AID
Motor Will Not Rotate
1. Check for proper electrical connections to motor.
2. Check main power box for tripped circuit breaker.
3. Check thermal overload on motor.
Motor Hums Or Will Not Rotate At Correct Speed
1. Check for proper electrical connections to motor and proper cord size and length.
2. Check for foreign material inside pump.
3. Remove volute and check for impeller rotation without excessive resistance.
4. Remove pump and check shaft rotation for excessive bearing noise.
5. Check start switch and/or capacitor.
Pump Operates With Little Or No Flow
1. Check to insure that pump is primed.
2. Check for leaking seal.
3. Improper line voltage to motor or incorrect rotation.
4. Check for clogged inlet port and/or impeller.
5. Defective check or foot valve.
6. Check inlet lines for leakage, either fluid or air.
Pump Loses Prime
1. Defective check or foot valve. 2. Inlet line air leakage.
3. Seal leaking. 4. Fluid supply low.
Motor Or Pump Overheats
1. Check for proper line voltage and phase, also proper motor wiring.
2. Binding motor shaft or pump parts.
3. Inadequate ventilation.
4. Fluid being pumped should not exceed 194°F (90°C) for extended periods of time
Gasgacinch® is a registered trademark of Porter Manufacturing. Noryl® is a registered trademark of
the General Electric Company. Teflon® is a registered trademark of DuPont Company. Permatex® is
a registered trademark of: ITW. Advance is a registered trademark of MDM Incorporated.
Advance® 4000 Installation Manual.indd Adobe Indesign CC 06-06-14
Please fill in for future reference:
MODEL:
___________________________
SERIAL NUMBER:
____________________
DATE PURCHASED:
___________________
* Please fill out the warranty registration
card included with this product or online at:
www.mdminc.com
MDM INCORPORATED
3345 N. Cascade Ave • Colorado Springs, CO • 80907
Toll Free Phone (800) 447-8342 • Fax (866) 425-1346
www.mdminc.com • [email protected]
