manualshive.com logo in svg

MDC XT17HRT 2022, Owner'S Manual

The MDC XT17HRT 2022 is an exceptional recreational trailer designed for outdoor enthusiasts. For a hassle-free experience, make sure to download the free Owner's Manual from manualshive.com to unlock valuable insights and instructions. This comprehensive manual will enhance your understanding of the product, maximizing your adventures.

Share
Download
background image

www.marketdirect.com.au

 

I

 

Ph: 1300 494 494

 

I

 

©Copyright

 I 

P a g e

 | 

32

Connecting the Breakaway 

The breakaway lanyard is connected to a simple switch on the drawbar. When connecting the lanyard to the tow 

vehicle it should be connected to a solid part of the vehicle. Do not incorporate its connection with the safety 

chains. 

    

Breakaway Switch  

 Lanyard Connection 

•

DO NOT CONNECT THE BREAKAWAY LANYARD TO THE SAME POINT AS THE SAFETY CHAIN

SHACKLES.

•

DO NOT USE THE BREAKAWAY AS AN ALTERNATIVE TO THE HANDBRAKE AND DO NOT

REMOVE THE PIN AS AN ALTERNATIVE SECURITY MEASURE. REMOVING THE PIN WILL

RAPIDLY DISCHARGE THE BATTERIES.

•

IT IS A MANDATORY REQUIREMENT THAT THE BREAKAWAY BATTERY SOURCE BE CHARGED

DURING TOWING.

•

NSW REQUIRES A BATTERY MONITOR VIEWABLE FROM THE DRIVERS POSITION WITH A

MINIMUM OF A VISUAL ALARM FOR LOW BATTERY VOLTAGE

Summary of Contents for XT17HRT 2022

















































































































Reviews:

No comments

Related manuals for XT17HRT 2022

Brands by name

Popular brands

Load more brands