McLaren coupe series Owner'S Handbook Manual Download Page 93 | Manualshive

Page: 93 / 272

background image

Driving Controls

Starting and Driving

2.13

ENVIRONMENTAL: When starting from
cold, gear changes occur at higher
engine speeds. The catalytic converter
will reach its operating temperature
quicker and reduce engine emissions.

1. With the engine running, press and hold

the brake pedal.

2. Select drive or reverse gear, or initiate

an upshift by operating the gearshift
paddles. For more information, see
Gearshift paddles, page 2.20 and Gear
positions, page 2.17.

3. Keep the brake pedal depressed and

release the parking brake switch. The
red status light in the instrument
cluster will be extinguished.

WARNING: If the parking brake is
manually released, the vehicle may
start to move.

NOTE: If the parking brake is not
manually released, it will
automatically release as the vehicle is
driven off forward, or in reverse as
long as the following conditions are
met:

•

all doors are closed

•

driver’s seat belt is buckled

4. Carefully depress the accelerator pedal.

Engine warning light

This engine warning light illuminates
when the ignition is on and

extinguishes as soon as the engine is
started, provided no faults exist.

If the light illuminates while driving, an
engine management fault has been
detected and reduced engine performance
may be experienced. Stop the vehicle as
soon as safety permits and contact your
McLaren retailer immediately.

Limphome mode

Limphome mode activates automatically
when vehicle systems detect a fault which
may cause further damage unless vehicle or
system performance is restricted. Care
should be taken while driving in this mode.
Contact your McLaren retailer immediately.

Economical driving

Improved fuel economy can be achieved by
following this advice:

•

Accelerate smoothly and gently from a
standing start.

•

When in manual mode, avoid high
engine rpm by changing to a higher
gear as soon as possible.

The Gear Shift Indicator (GSI) will
illuminate when an upshift would

maintain optimum economy.

NOTE: Not available in all markets,
consult your McLaren retailer.

•

Avoid laboring or over-revving the
engine.

•

Switch off the air conditioning when it
is not needed.

•

Avoid journeys where frequent stop
start driving is involved.

•

Ensure that your driving style suits the
prevailing road and traffic conditions;
allow time for smooth, progressive
acceleration and braking.

•

Use a reputable fuel economy tracking
website to track your mileage and fuel
usage.

p13.book Page 13 Wednesday, April 26, 2017 9:22 PM

«
...
91
92
93
94
95
...
»

Summary of Contents for coupe series

















































































































































































































































































Reviews:

No comments

Related manuals for coupe series

Brand: LaserTrack Pages: 12

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: HALE Pages: 44

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

Brand: TATA Motors Pages: 156

Brand: SnapPad Pages: 5

Escalade ESV 2014

Brand: Cadillac Pages: 508

Brand: Hama Pages: 2

Brand: Parkeon Pages: 43

Brand: Volvo Pages: 266

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands