6"
/8"
Commercial
LED
Retrofit
Downlight
User Manual
The units covered in th
ese instructions
are Type IC
,
Type
Non-IC
luminaires.
2.
Commercial installation: Service and maintenance of Commercial Downlights should be
performed by a qualified electrician.
WARNING / ATTENTION
:
1.
3.
Risk of fire
,
electric shock
or death
. If not qualified, do not attempt installation.
SAFETY:
1. For your safety read and understand instructions completely before starting installation.
2
.
The fixture must be wired in accordance with the National Electric Code and applicable
local codes or ordinances.
Contact a
qualified electrician.
Approved Dimmers:
Lutron
(0-10V Reqd.)
:
DVDT, NTSTV-DV
www.maxximastyle.com
Luminous Intensity Distribution Diagram
s
:
Residential installation: If you are unsure about the installation or maintenance of the
Commercial Downlight, please consult a
qualified electrician for 120 VAC service.
Do not attempt greater than 120VAC installations unless you are a qualified electrician
because severe life threatening electrical shock can occur.
3
.
To insure personal safety, proper grounding and use of safety cable is required.
Maxxima extends a 5 year limited warranty to the original purchase that the products listed are free from defects in material and/or
workmanship only. Maxxima will replace any warranteed product to the original consumer/purchaser if the product fails because of defects
due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby
assume any obilgation whatsoever beyond sending a free replacement product.
5 Year Warranty:
Figure 1 -
MRL-61800CNW LIDD
Figure
2
-
MRL-
827
00CNW LIDD
1-866-MAXXIMA
Model
Input Voltage (V) Input Frequency (Hz) Input Current (A) Input Watts (W)
MRL-61
800CNW
1
0
0
-277VAC
50/
60
0.
25
1
8
Electrical Ratings:
1.
Install wire: Push gray or orange WIRE
CAPTURE down, insert wire thru hole in plate,
release WIRE CAPTURE.
2. Remove wire: Push gray or orange
WIRE CAPTURE down, remove wire, r
elease WIRE CAPTURE.
4 each
WIRE CAPTURE
S per Terminal Block
to
LED Lamp
to Facility
(VAC/dimmer)
Dimensions
& Compatibility
:
IMPORTANT INSTALLATION NOTE: P/N on LED Driver must match P/N on LED Lamp!
INSTALLATION NOTE: Reflector may be separated and reattached to LED Lamp by 3 latches.
MRL-61800CNW -
Recessed LED Lamp with Reflector: 7.
5
" (DIA) X 8.
6
" (H)
(fits 6" to 6.7"
opening
)
MRL-82700CNW - Recessed LED Lamp with Reflector: 9.3" (DIA) X 9.0" (H) (fits
7.7
" to
8.4
" f
opening
)
LED Driver
(P/N MUST match LED Lamp)
: 7.1" L x 2.7" W x 1.4" D (plus
(qty. 3)
mounting
tabs
)
Whips (
LED Driver
-
Flexible Metal Conduit
s)
:
1/2" x
14"
length
each
(
with
snap-tite connectors)
Wiring
labeled on LED Driver
Figure
3
- LED Driver (
pre-wired as shown
)
Figure
4
- LED Driver & LED Lamp
(
t
op view)
MRL-
827
00CNW
1
0
0
-277VAC
50/
60
0.
35
27
LED Driver - Terminal Block Use (comes pre-wired)
:
Figure
5
-
6"
MRL-61800CNW
LED Lamp
Figure
6
-
8"
MRL-
827
00CNW
LED Lamp