Maxwell MW-3055 B Manual Instruction Download

Page: 12 / 36

ENGLISH

–

Once the soleplate (14) reaches the preset
temperature, the pilot lamp (9) will go out,
you can start ironing.

–

Set the necessary steam intensity (from «

•

to « ») with the continuous steam supply
knob (3).

–

In the continuous steam supply mode, steam
will be released from the openings of the
soleplate (14) only if the iron is in horizontal
position. To stop the steam supply, put the
iron vertically or set the knob (3) to the posi-
tion «

•

» (steam supply is off).

–

After you finish ironing, set the temperature
control knob (11) to the «MIN» position, and
the continuous steam supply knob (3) to the
position «

•

» (steam supply is off).

–

Pull the power plug out of the mains socket
and let the iron cool down completely.

ATTENTION!
If steam is not supplied constantly during the
operation, check whether the steam supply con-
trol (3) is set properly and whether there is water
in the water tank (10).

WATER SPRAY

–

You can dampen the fabric by pressing the
spray button (5) several times.

–

Make sure that there is enough water in the
water tank (10).

BURST OF STEAM
The burst of steam function is useful when iron-
ing of folds and can only be used at high ironing
temperatures (when the temperature control
knob (11) is set to «MAX» position).
When the burst of steam button (4) is pressed,
steam is being released from the soleplate (14)
openings intensively.

Notes: To avoid water leakage from the steam
openings, press the burst of steam button (4)
with 4-5 sec. intervals.
To avoid dripping, do not hold the burst of steam
button (4) longer than 5 seconds.

VERTICAL STEAM
The  vertical  steam  function  can  be  used  only
at  high  ironing  temperatures  (when  the  tem-
perature  control  knob  (11)  is  set  to  the  «MAX»
position).
Hold  the  iron  vertically  at  the  distance  of
10-30 cm from the clothes and press the burst
of steam button (4) with a 4-5 seconds interval,

steam will be released from the soleplate (14)
intensively.

Important information
Vertical steam is not recommended for synthetic
fabrics.

–

To avoid fabric melting, do not touch it with
the iron’s soleplate while steaming.

–

Never steam clothes on a person as the
steam temperature is very high, use a clothes
hanger or a stand.

–

After you finish ironing, switch the unit off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.

STEAM CHAMBER CLEANING
To prolong service life of the iron, clean the
steam chamber regularly, especially in the
regions with hard tap water.

–

Set the continuous steam supply knob (3) to
the position «

•

» (steam supply is off).

–

Fill the water tank (10) till the «MAX» mark
(13).

–

Place the iron on its base (8).

–

Insert the power plug into the mains socket.

–

Set the control knob (11) to the maximum
soleplate temperature «MAX», the pilot lamp
(9) will light up.

–

Once the iron soleplate (14) reaches the set
temperature, the pilot lamp (9) will go out.
Wait until the iron soleplate is reheated, then
you can start cleaning the steam chamber.

–

Unplug the unit.

–

Hold the iron above the sink horizontally,
press and hold the “Self Clean” button (12).

–

Boiling water and steam with scale will be
released from the iron soleplate (14) open-
ings.

–

Slightly sway the iron back and forth, until all
the water leaves the water tank (10).

–

Place the iron on the base (8) and let it cool
down completely.

–

When the soleplate (14) cools down com-
pletely, wipe it with a dry cloth.