12
ENGLISH
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.maxwell-products.ru.
•
Transport the unit in the original package only.
•
Keep the unit out of reach of children and dis-
abled persons.
•
This unit is not intended for usage by chil-
dren. Place the unit out of reach of children
during the operation and cooling down.
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience or
knowledge if they are not under supervision
of a person who is responsible for their safety
or if they are not instructed by this person on
the usage of the unit.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
•
Unpack the iron; remove the protection from
the soleplate (13), if any.
•
Check the unit for damages; do not use the
iron in case of damages.
•
Before switching the iron on, make sure that
your home mains voltage corresponds to the
iron operating voltage.
•
There may be water residue in the tank, this
is normal, as the iron has undergone factory
quality control.
Notes:
When the iron is switched on for the
first time, the heating element of the iron
burns, therefore occurrence of foreign smell
and a small amount of smoke is possible, it
is normal.
Control knobs, indications and symbols
•
The continuous steam supply knob (3) has
two fixed positions:
–
o – steam supply is off;
–
– steam supply is on;
and one more position:
–
SELF CLEAN – self-clean.
•
Burst of steam button (4):
–
press the button to activate the additional
steam supply function.
•
Water spray button (5):
–
press the button to activate the water
spray function.
•
Heating element ON/OFF indicator (11)
–
when the indicator lights up, the iron sole-
plate is heating up.
•
Temperature control knob (9):
–
allows setting the iron soleplate tempera-
ture depending on the type of fabric (see
the table below). The knob is in the posi-
tion
«MIN»
– the iron is off.
•
«MAX»
maximal water level mark.
•
The symbol
indicates hot surfaces.
WATER SELECTION
You can use tap water to fill the water tank (10).
If tap water is hard, use distilled or demineralized
water, this will prolong service life of the iron.
Note:
Do not fill the water tank 10) with scent-
ed liquids, vinegar, starch solution, descaling
reagents, chemical agents, etc.
FILLING THE WATER TANK
Before filling the iron with water, make sure that
it is unplugged.
•
Set the temperature control knob (9) to the
«MIN»
position and turn the continuous
steam supply knob (3) to the position «о» –
continuous steam supply is off.
•
Open the water inlet lid (2).
•
Pour water into the water tank (10) and then
close the water inlet lid (2) tightly.
Notes:
•
Do not exceed the «
MAX
»
mark (12).
•
If you need to refill water during ironing,
switch the iron off and unplug it.
•
After you finish ironing, switch the iron off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.
IRONING TEMPERATURE
Before operation, test the heated iron on a piece
of cloth to be sure that the iron soleplate (13) and
the water tank (10) are clean.
•
Always check the recommended ironing
temperature indicated on the tag before
ironing.
IM MW-3042.indd 12
13.05.2016 16:01:34