12
ENGLISH
mix it with distilled water in proportion 1:2 or use
distilled water only.
FILLING THE WATER TANK WITH WATER
Before filling the tank with water make sure that
the unit is unplugged.
•
Set the temperature control knob (10) to the
«MIN» position and the continuous steam
supply knob (3) to the position « » (continu-
ous steam supply is off).
•
Open the water inlet lid (2).
•
Fill the unit with water, using the beaker (15),
then close the lid (2) tightly.
Note:
•
Do not exceed the “MAX” mark (11).
•
If you need to refill water during ironing,
switch the iron off and unplug it.
•
After you finish ironing, switch the unit off,
wait until it cools down completely, then open
the water inlet lid (2), turn over the iron and
drain the remaining water.
IRONING TEMPERATURE
Before operating test the heated iron on a piece
of cloth to be sure that iron soleplate (14) and the
water tank (13) are clean.
•
Always check the recommended iron tem-
perature indicated on the tag before ironing.
•
If there is no tag with recommendations for
ironing, but you know the type of fabric, use
the following table to determine the proper
temperature.
Icons of
the ironing
temperature
Fabric type
•
Synthetics, nylon, acrylic,
polyester, acetate (low
temperature)
-
dry ironing only
••
Silk/wool (medium temperature)
•••
Cotton, linen (high temperature)
MAX
Maximum temperature
•
This table is only valid for smooth materials.
Fabrics of other types (crimped, raised etc.)
are best ironed at low temperature.
•
Sort items by ironing temperature first: syn-
thetics with synthetics, wool with wool, cotton
with cotton etc.
•
The iron heats up faster than it cools down.
For this reason it is recommended to start
ironing at low temperature (for instance, syn-
thetic fabrics).
•
After that, continue ironing at higher tem-
perature (silk/wool). Cotton and linen items
should be ironed last.
•
If an item is made of mixed fabrics, the iron
should be set to the lowest temperature (for
instance, if an item is made of polyester and
cotton, it should be ironed at temperature
used for polyester ironing «•»).
•
If you cannot define the fabric structure,
find a place that is hidden while wearing and
select the ironing temperature experimentally
(always start with the lowest temperature and
raise it gradually until you get the desired
result).
•
Corduroy and other fabrics that become
glossy quickly should be ironed strictly in
one direction (in direction of the pile) slightly
pressing.
•
To avoid appearance of glossy spots on syn-
thetic and silk fabrics, iron them backside.
SETTING THE IRONING TEMPERATURE
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket.
•
Turn the temperature control knob (10) to set
the required ironing temperature: “•”, “••”,
“•••” or “MAX” (depending on the type of
fabric), the pilot lamp (6) will light up.
•
Once the soleplate temperature (14) reaches
the set one, the pilot lamp (6) will go out, you
can start ironing.
DRY IRONING
•
Set the continuous steam supply knob (3) to
the position « » (steam supply is off).
•
Place the iron on its base (9).
•
Insert the power plug into the mains socket.
•
Turn the temperature control knob (10) to set
the required ironing temperature: “•”, “••”,
“•••” or “MAX”, (depending on the type of
fabric), the pilot lamp (6) will light up.
•
Once the soleplate temperature (14) reaches
the set one, the pilot lamp (6) will go out, you
can start ironing.
•
After you finish ironing set the temperature
control knob to the “MIN” position.
MW-3018.indd 12
12.02.2014 16:57:45
Summary of Contents for MW-3018 BK
