9
ENGLISH
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger
of suffocation!
•
Close supervision is necessary when chil-
dren or disabled persons are near the oper-
ating unit.
•
The unit is not intended for usage by physi-
cally or mentally disabled persons (including
children) or by persons lacking experience or
knowledge if they are not under supervision
of a person who is responsible for their safety
or if they are not instructed by this person on
the usage of the unit.
•
Do not leave children unattended to prevent
them from using the unit as a toy.
•
Never use the unit if the power cord or the
power cord plug is damaged, if the unit works
improperly or after it was dropped.
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and contact any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.maxwell-products.ru.
•
Transport the unit in the original packaging
only.
•
Keep the unit out of reach of children and
people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES
IS PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature keep it for at least 3 hours at
room temperature before switching on.
There may be water spots in the thermopot, this
is normal, as the unit has undergone factory
quality control.
•
Unpack the thermopot; remove any advertis-
ing stickers that can prevent the unit opera-
tion.
•
Check the unit for damages, do not use it in
case of damages.
•
Make sure that the unit operating voltage
corresponds to the voltage of your mains.
•
Place the thermopot on a dry flat surface
keeping at least 20 cm gap between the ther-
mopot body and the wall or furniture and at
least 30 cm gap above the thermopot.
•
Open the lid (8) by pressing the front part of
the button (9) and holding it.
•
Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (13) «Макс.».
•
Insert the power cord (18) connector into the
socket (16) on the thermopot body, and plug
the power cord (18) into the mains socket.
•
The boiling mode indicator «BOILING» (6) will
light up on the control panel (4).
•
After water starts boiling, the thermopot will
be switched to the keep warm mode, the
indicator (6) will go out and the indicator (7)
«KEEP WARM» will light up.
Note: - the thermopot uses a long boiling tech-
nology which allows to significantly reduce the
chlorine level in water.
•
Drain the water; to do this set the lock (12)
to the position « » and press on the hand
pump (10).
Attention! Be careful when pouring out water to
avoid burns by hot water.
•
Switch the thermopot off, to do this discon-
nect the power cord (18) plug from the mains
socket and disconnect the power cord (18)
connector from the socket (16).
•
Open the thermopot lid (8) and wait until it
cools down completely.
•
To remove the lid (8) slightly open it and pull
the lid (8) towards yourself taking it by both
sides.
•
Carefully tilt the thermopot to drain the
remaining water.
•
Install the lid (8) back to its place; to do this
match the ledges on the rear part of the
lid (8) with the grooves in the lid installation
place. Slightly lift the lid and press on it from
both sides to fix. Before using the thermopot
make sure that the lid (8) is fixed properly.
USAGE OF THERMOPOT
•
Open the lid (8) by pressing the button (9)
and holding it.
•
Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (13) «Макс.».
•
Insert the power cord (18) connector into the
socket (16) on the thermopot body, and plug
the power cord (18) into the mains socket.
•
The boiling mode indicator «BOILING» (6) will
light up on the control panel (4).
•
After water starts boiling, the thermopot will
be switched to the keep warm mode, the
MW-1755.indd 9
18.07.2018 16:47:13
