10
ENGLISH
indicator (6) will go out and the indicator (7)
«KEEP WARM» will light up.
•
In the keep warm mode you can switch
the reboiling on by pressing the button (5)
«REBOIL», the indicator (6) «BOILING» will
light up and the indicator (7) will go out.
•
Drain the water; to do this set the lock (12)
to the position «
» and press on the hand
pump (10).
Attention! Be careful when pouring out water to
avoid burns by hot water.
•
Lock the hand pump by setting the lock (12)
to the position « ».
•
After you finish using the thermopot, dis-
connect the power cord (18) plug from the
mains, disconnect the power cord (18) con-
nector from the socket (16), open the ther-
mopot lid (8) and wait until it cools down
completely. Remove the lid (8), drain the
water, dry the unit, install the lid (8) back to
its place and take the thermopot away for
storage.
CLEANING AND CARE
•
Before cleaning, disconnect the thermopot
from the mains, pour out water and let the
thermopot cool down completely.
•
To remove the lid (8) slightly open it and pull
the lid (8) towards yourself taking it by both
sides.
•
Carefully tilt the thermopot to drain the
remaining water.
•
Install the lid (8) back to its place; to do this
match the ledges on the rear part of the lid
(8) with the grooves in the lid installation
place. Slightly lift the lid and press on it from
both sides to fix. Before using the thermopot
make sure that the lid (8) is fixed properly.
•
Clean the outer surface of the thermopot
body (15) with a slightly damp cloth and then
wipe it dry.
•
Use neutral detergents to remove dirt; do not
use metal brushes and abrasive detergents.
•
Do not immerse the thermopot and the power
cord into water and other liquids.
•
Do not wash the thermopot in a dishwashing
machine.
Stains on the inner surface
of the thermopot
The inner surface of the metal flask may change
its color under the influence of different water
impurities.
•
You can remove the stains with citric acid or
vinegar.
•
To remove the flavour of citric acid or vinegar,
boil water and pour it out.
•
Repeat this procedure until the smell and
taste vanish completely.
Descaling
•
Scale, appearing inside the metal flask, influ-
ences the water taste and disturbs the heat
exchange between water and the heating
element, that can lead to overheating and
malfunction.
•
To remove the scale fill the thermopot with a
mixture of one part ordinary vinegar and two
parts water up to the maximal level mark (13)
«Макс.».
•
Insert the power cord (18) connector into the
socket (16) on the thermopot body, and plug
the power cord (18) into the mains socket.
•
The boiling mode indicator «BOILING» (6) will
light up on the control panel (4).
•
After water starts boiling, the thermopot will be
switched to the keep warm mode, the indicator
(6) will go out and the indicator (7) will light up.
•
Unplug the thermopot and leave it filled with
the vinegar solution overnight.
•
In the morning pour out the vinegar solution,
fill the thermopot with water up to the maxi-
mal level mark (13) «Макс.», boil it and pour
out the water.
•
You can use special detergents for electric
kettles to remove scale, strictly following the
instructions on the detergent usage.
•
If necessary, perform the cleaning procedure
several times.
STORAGE
•
Before taking the thermopot away for long
storage, unplug it, let the unit cool down and
pour out the remaining water.
•
Clean the thermopot.
•
Keep the thermopot out of reach of children
and disabled persons.
DELIVERY SET
Thermopot – 1 pc.
Manual – 1 pc.
TECHNICAL SPECIFICATIONS
Power supply: 220-240 V ~ 50 Hz
Rated input power: 750 W
Maximal water capacity 3 L
MW-1755.indd 10
18.07.2018 16:47:13
