Maxsys PC4164-433 Installation Manual Download Page 1

FCC COMPLIANCE STATEMENT

CAUTION: 

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY DIGITAL SECURITY

CONTROLS LTD. COULD VOID YOUR AUTHORITY TO USE THIS EQUIPMENT.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance
with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested
and found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part
15 of FCC Rules, which are designed to provide reasonable protection against such interference in any residential
installation. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to television or radio reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Re-orient the receiving antenna

Relocate the alarm control with respect to the receiver

Move the alarm control away from the receiver

Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and Resolve
Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office,
Washington, D.C. 20402, Stock # 004-000-00345-4.

©2002 Digital Security Controls Ltd.
Toronto, Canada  •   

www.dsc.com

Technical Support  1-800-387-3630
Printed in Canada   29034504 R002

Direct all comments and sugges-
tions concerning DSC publications

to 

[email protected]

(Outside of North America, please contact your authorized DSC distributor for technical support)

WARNING:

 

This manual contains information on limitations regarding product

use and function and information on the limitations as to liability of the

manufacturer. The entire manual should be carefully read.

®

PC4164-433 v3.0 

• Installation Manual

This PC4164-433 V3.0 receiver version is currently
supported by all PC4010/PC4020/P-16128 V3.x DLS-3
downloading files.

https://www.e-camere.ro/alarma-antiefractie/module/DSC/PC-4164/

Summary of Contents for PC4164-433













Reviews: