maxon motor EPOS4 Compact 50/8 CAN Hardware Reference Manual Download Page 79

Page: 79 / 106

Setup

Status Indicators

maxon motor control
EPOS4 Positioning Controller

Document ID: rel8399

3-79

EPOS4 Module/Compact 50/8 Hardware Reference

Edition: November 2018

3.5.1

NET Status

The LEDs (



Figure 3-53;

) display the actual status and possible errors of the EPOS4 in respect to

the NET network:

•

Green LED shows the RUN state

•

Red LED indicates errors

Table 3-69

NET Status LEDs

LED

Description

Green

Red

OFF

—

EPOS4 is in state INIT

Blink

—

EPOS4 is in state PRE-OPERATIONAL

Single flash

—

EPOS4 is in state SAFE-OPERATIONAL

—

EPOS4 is in state OPERATIONAL

Flicker

—

EPOS4 is in state BOOTSTRAP

—

OFF

EPOS4 is in operating condition

—

Double flash

An application watchdog timeout has occurred

Example: Timeout of Sync Manager Watchdog

—

Single flash

EPOS4 has changed the COM state due to an internal error

Example: Change of state “Op” to “SafeOpError” due to Sync Error

—

Blink

General Configuration Error

Example: State change commanded by master is not possible due to
actual settings (register, object, hardware configuration)

Blink = continuous blinking (

≈

2.5 Hz)

Flash = flashing (

≈

0.2 s), followed by pause of 1 s

Flicker = continuous flickering (

≈

10Hz)

Summary of Contents for EPOS4 Compact 50/8 CAN











































































































Search results

Summary of Contents for EPOS4 Compact 50/8 CAN

Reviews:

Related manuals for EPOS4 Compact 50/8 CAN

Brands by name

Popular brands

maxon motor EPOS4 Compact 50/8 CAN, Hardware Reference Manual

Search results

Summary of Contents for EPOS4 Compact 50/8 CAN

Reviews:

Related manuals for EPOS4 Compact 50/8 CAN

Brands by name

Popular brands