manualshive.com logo in svg

Maxim Dallas Semiconductor DS3171, General Description Manual, Page: 166 / 234

Share
Download
Maxim Dallas Semiconductor DS3171 General Description Manual Download Page 166

DS3171/DS3172/DS3173/DS3174 

 

 

166 

Register Name: 

FEAC.TFDR 

Register Description: 

Transmit FEAC Data Register 

Register Address: 

(0,2,4,6)C2h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name 

-- 

-- 

TFCB5 TFCB4 TFCB3 TFCB2 TFCB1 TFCB0 

Default 

0 0 0 0 0 0 0 0 

 
Bit 

# 7 6 5 4 3 2 1 0 

Name 

-- 

-- 

TFCA5 TFCA4 TFCA3 TFCA2 TFCA1 TFCA0 

Default 

0 0 0 0 0 0 0 0 

 

Bits 13 to 8: Transmit FEAC Code B

 

(TFCB[5:0])

 – These six bits are the transmit FEAC code B data to be 

stored inserted into codeword B. TFCB[5] is the LSB (last bit transmitted) of the FEAC code (C[6]), and TFCB[0] is 
the MSB (first bit transmitted) of the FEAC code (C[1]). 

Bits 5 to 0: Transmit FEAC Code A

 

(TFCA[5:0])

 – These six bits are the transmit FEAC code A data to be stored 

inserted into codeword A. TFCA[5] is the LSB (last bit transmitted) of the FEAC code (C[6]), and TFCA[0] is the 
MSB (first bit transmitted) of the FEAC code (C[1]). 

 

 
Register Name: 

FEAC.TSR 

Register Description: 

FEAC Transmit Status Register 

Register Address: 

(0,2,4,6)C4h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name 

-- -- -- -- -- -- -- -- 

 
Bit 

# 7 6 5 4 3 2 1 0 

Name 

-- -- -- -- -- -- -- TFI 

 

Bit 0: Transmit FEAC Idle (TFI)

 – When 0, the Transmit FEAC processor is sending a FEAC codeword. When 1, 

the Transmit FEAC processor is sending an Idle signal (all ones). 

 

 
Register Name: 

FEAC.TSRL 

Register Description: 

FEAC Transmit Status Register Latched 

Register Address: 

(0,2,4,6)C6h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name 

-- -- -- -- -- -- -- -- 

 
Bit 

# 7 6 5 4 3 2 1 0 

Name 

-- -- -- -- -- -- -- 

TFIL 

 

Bit 0: Transmit FEAC Idle Latched (TFIL)

 – This bit is set when the TFI bit transitions from 0 to 1. Note: 

Immediately after a reset, this bit will be set to one. 

 

 

 

Summary of Contents for Dallas Semiconductor DS3171











































































































































































































































Reviews:

No comments